Editing Rewiring a vehicle
Line 1: | Line 1: | ||
− | + | {{youcanedit}} | |
==Overview== | ==Overview== | ||
When completely rewiring a vehicle there are a few things that must be determined beforehand. First, one must decide if a prefabricated harness will be used, or if a custom harness will be made from scratch. In any case, the harness should be assembled into groups and cut within a reasonable distance to the right length, while leaving extra wire to account for routing. | When completely rewiring a vehicle there are a few things that must be determined beforehand. First, one must decide if a prefabricated harness will be used, or if a custom harness will be made from scratch. In any case, the harness should be assembled into groups and cut within a reasonable distance to the right length, while leaving extra wire to account for routing. | ||
Line 48: | Line 48: | ||
===If soldering:=== | ===If soldering:=== | ||
+ | |||
*Good soldering station (don't use an undersized or non-controlled unit; it will slow things down) | *Good soldering station (don't use an undersized or non-controlled unit; it will slow things down) | ||
*Solder (24 gauge 60/40 is good) | *Solder (24 gauge 60/40 is good) | ||
Line 88: | Line 89: | ||
#Do the same for the whole diagram. You can get software to make your own schematic on your computer. This is where all your notes and line drawing will merge into a single easy-to-read schematic, which will be useful in the future. | #Do the same for the whole diagram. You can get software to make your own schematic on your computer. This is where all your notes and line drawing will merge into a single easy-to-read schematic, which will be useful in the future. | ||
#Next, one last time, ring or continuity check your harness point to point with an OHM meter or ring box. Make sure your connections are correct, and conducting, and conform to your line drawing (you can do both steps at the same time). Once you confirm all is correct, you can power test the system. | #Next, one last time, ring or continuity check your harness point to point with an OHM meter or ring box. Make sure your connections are correct, and conducting, and conform to your line drawing (you can do both steps at the same time). Once you confirm all is correct, you can power test the system. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
==Testing== | ==Testing== | ||
Line 132: | Line 97: | ||
The second recommendation is a motorcycle battery (not a big Harley batter, a small hold-in-your-hand Honda-type battery). Install a 30 amp fuse link on the positive, and, (if your meter supports it) use your meter in line to monitor current. At this point you will be doing no "high current testing" so you should be good. If not a motorcycle battery, two parallel connected lantern batteries should last long enough to do some primary testing. | The second recommendation is a motorcycle battery (not a big Harley batter, a small hold-in-your-hand Honda-type battery). Install a 30 amp fuse link on the positive, and, (if your meter supports it) use your meter in line to monitor current. At this point you will be doing no "high current testing" so you should be good. If not a motorcycle battery, two parallel connected lantern batteries should last long enough to do some primary testing. | ||
− | + | Lastly, if you must use a battery charger, disconnect ANY electronics you have: CD player, tach, ECU, ECM, alternator, regulator, digital dash displays, and anything solid state to avoid damage. | |
Whatever system approach you take, test for functionality, correct any errors you may find. | Whatever system approach you take, test for functionality, correct any errors you may find. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
==Miscellaneous== | ==Miscellaneous== | ||
Line 164: | Line 120: | ||
[[Category:Ignition]] | [[Category:Ignition]] | ||
[[Category:Electrical]] | [[Category:Electrical]] | ||
+ | {{youcanedit} |