Editing Quadrajet

The '''Quadrajet''' is a 4 barrel [[carburetor]] made by the [[Rochester Products Division]] of GM that was widely used in [[General Motors]] motor vehicles until 1990.  Its last application was on the [[Oldsmobile V8 engine#307|Oldsmobile 307]] V8 engine, which was last used in the [[Cadillac Brougham]] and full size [[station wagons]] made by [[Chevrolet]], [[Pontiac]], [[Oldsmobile]], and [[Buick]].

The Quadrajet has been described as one of the best carburetors made for passenger vehicles, offering the best compromise of [[Fuel economy in automobiles|fuel economy]], performance, driveability, and [[automobile emissions control]].{{Fact|date=July 2007}}

==Design==
The Quadrajet is a "spread bore" carburetor; the primary [[venturi]]s are much smaller than the secondary venturis.  By comparison, a "square bore" carburetor has primary and secondary venturis of similar if not exactly the same size.  Most Quadrajets were capable of 750 [[cubic feet per minute]] (CFM) maximum, but some were manufactured as 800 CFM for use on high performance engines.  Most Quadrajets use a vacuum operated piston to move the primary metering rods to control the (air fuel ratio), allowing the mixture to be lean under low load conditions and rich during high load conditions.  A less-common version uses a linkage driven off the primary throttle shaft to mechanically move the power piston.  "E" (Electronic Control Module controlled) series of Quadrajets use a computer controlled Mixture Control Solenoid that responds to electronic signals from the throttle position sensor, ideal for precise fuel metering and allowing additional fuel under load.  The solenoid-controlled metering rods allow the fuel mixture to be very close to optimum, then the solenoid is [[Pulse-width modulation|pulse width modulated]] at about 6 Hz to fine-tune the air fuel ratio under closed loop conditions.  The electronic versions have a throttle position sensor that is mounted inside the carburetor body, actuated by the accelerator pump lever.

Quadrajet carburetors have mechanical secondary throttle plates operated by a progressive linkage (primaries open before secondaries) but use "on-demand" air valve plates above the secondary throttle plates.  The air valves are connected by a cam and linkage to the secondary fuel metering rods.  As the airflow increases through the secondary bores, the air valves are pushed down, rotating a cam that lifts the secondary metering rods.  The secondary rods are tapered in a similar fashion to the primary metering rods, effectively increasing the size of the fuel metering holes as the rods are lifted and delivering more fuel.  Therefore, the position of the air valve will control both fuel and air flow through the secondary venturis, even if the secondary throttle plates are fully opened. The end result is that the Quadrajet acts like a "vacuum secondary" carburetor and only delivers more fuel as it is needed.

==Advantages==
Significant positive features of the Quadrajet were:
# Economy.  Unlike most other 4-barrel carburetors, the Quadrajet has a drastically different sized primary and secondary bores. The much smaller primaries act as a small two-barrel carburetor until you press the throttle enough to start to open the secondaries.  The small primaries allow the primary throttle plates to be opened wider, and thus making the carburetor more efficient than a large two barrel, or square bore four-barrel.
# Drivability.  The small primaries also create better throttle response at part throttle application.  The Quadrajet had a centrally located float that gave it excellent fuel control resulting in excellent street manners.
# Off Road.  The Quadrajet’s centrally located float is highly resistant to level changes caused by cornering or acceleration.

==Drawbacks==
Significant negative features of the Quadrajet were:
# Its leaky fuel bowl.  As in nearly all carburetors, the Quadrajet's bowl had pressed-in plugs used to seal holes left after drilling fuel passages during the manufacturing of the carburetor.  These plugs in the Q-jet sometimes leaked fuel causing; (a) a cold engine being hard to start, (b) erratic idling, (c) poor fuel mileage, and (d) excessive emissions.  Many Quadrajets have their fuel bowl plugs sealed with [[epoxy]] when rebuilt to prevent leaks.
# The very small float bowl/fuel chamber can result in fuel starvation in extreme high-performance situations, but can usually be traced to a fuel delivery problem to the carburetor, such as a worn fuel pump or camshaft.  In normal driving and mild performance use it provides excellent control of fuel level.
# The fuel inlet/fuel filter housing threads tend to be very fragile.  It is common for the fuel inlet threads in the main casting to strip.  There are several "fixes" available in the aftermarket:  New oversize self-tapping [[fuel filter]] housings; new fuel filter housings that seal with [[O-rings]]; and [[Heli-Coil]] rethreading kits.
# Almost all Quadrajets today have some amount of warpage of the castings.  The root cause of this warpage is over-tightening the front two carburetor mounting bolts, often in combination with a base gasket that doesn't have hard [[nylon]] inserts for the bolt holes.
# The steel primary throttle shaft will tend to wear the aluminum casting material.  This results in an air leak and in extreme cases could cause the primary throttle blades to not close properly.  This results in poor idle quality.  The [[aftermarket]] has responded; several vendors are supplying repair kits for the carburetor body.

==Variants==
A major change to the Quadrajet was implemented for the 1975 model year.  These newer carburetors are considered "Modified Quadrajets" or "Mod Quads".  In addition to the casting revisions that result in a physically larger carburetor, the primary metering rod length is different from '74 and older Q-Jets.  They were also equipped with a self contained choke mechanism that no longer relied on an intake manifold mounted choke, and a number "1" was added to the beginning of their identification numbers.

Quadrajet carburetors were also built under contract by [[Carter]].  This seems to have happened at times when Rochester's facility could not keep up with demand.  Carter-built Quadrajets will have the name "Carter" cast into them, but are functionally identical to the Rochester-built equivalent.  The "newest" Q-Jets were built for, and sold by [[Edelbrock]].  There were several versions made, for both stock replacement and "performance" applications.  One version was specifically intended as a replacement for Carter Thermoquad carburetors.  The Edelbrock Q-Jets have been discontinued, although at this time Edelbrock still supplies some replacement parts.

==References==

==See also==

==External links==


[[Category:Automotive technology tradenames]]