Editing Ford 9-inch rear ends

{{youcanedit}}
'''If you have a link to an article or web site that talks about nine inch rear ends, put the link here. If you want to write an article or a story about your experience with one, write it here. Hopefully, this will become a place that will answer all your questions on the nine inch.'''

== Alterations of nine inch ==
In order to install a pre-load brace, you will have to build a strong fixture to hold the housing while you apply force to the housing ends. You can be begin by purchasing 3-inch 1/4 or 3/8 wall tubing and cutting it to two pieces of six foot lengths. Cut a square piece of 1/2 inch plate @ 16 X 16 inches, place the center section over the plate and mark out the bolt pattern, go to the drill press after center punching the bolt centers on the plate, drill out the holes to 7/16 inches.

[[File:Brace_in_place.jpg]]

[[File:Center_plate_bolt_pattern.jpg]]

Mark out the center line of the two six-foot lengths, measure equal distant 8 inches for the 16 X 16 plate to lay on the cross pieces. Measure the distance between the two parallel pieces, cut two pieces of 3-inch tubing to this dimension and weld it using a stitch method, so as not to warp the fixture. Cut to appropriate pieces of 2 X 3 rectangular tubing, measure out from the center line noted above to the axle flanges and weld in the two cross pieces. Looking closely at the U-bolt picture, notice how the two angle irons keep the axle tubes centered in the fixture and how the U-bolts are mounted through the clamping plate.

[[File:Housing_in_fixture.jpg]]

[[File:U_bolts_in_place.jpg]]

After all welding is completed, lay the fixture on a flat surface, shim as required, place the housing in the fixture, bolt down the center section, place the U-bolts over the axle tubes, put the pre-load brace in place, measure from the outside flange to the outside flange, record the measurement. The turn down the U-bolts, which, in turn, will apply downward pressure to the axle tubes, re-measure from flange to flange, if the NEW figure is approximately 1/4 inch LONGER, start stitch welding the pre-load brace to the rear axle tubes. Watch the heat and watch for warping. Weld from side to side in small stitches. Let everything cool entirely before pulling out of jig, and you're done.

==Ford 9" rear end photographs==
[[Image:9_in_exp_view.gif‎ ]]

[[Image:9_in_case.jpeg‎ ]]

[[Image:9_in_rear.JPG]]

==Ford 9" rear end articles and information==
*http://www.maliburacing.com/ford_9_inch/ford_nine_inch.htm
*http://dfwmotorsport.com/Fairlane/9inchrearends.htm
*http://www.kevinstang.com/Ninecase.htm
*http://www.ridgenet.net/~biesiade/Fordrears.html
*http://www.chevyhiperformance.com/techarticles/0304_9_inch_12_bolt_rearend_comparison/index.html
*http://www.ford-trucks.com/article/idx/0/065/article/Ford_9_Inch_RebuildGear_Setup.html
*http://www.fordmuscle.com/archives/2006/04/9Inch/index.php
*http://www.fordmuscle.com/archives/2002/02/nineinch/
*http://www.fordmuscle.com/blog/free-a-stuck-pig/112171
*http://www.fordmuscle.com/forums/rear-end-articles/484585-fixing-9-ford-pinion-leaks.html
*http://www.enjenjo.com/9inch.html

==Suppliers and manufacturers of Ford 9" rear ends==
*[http://www.quickperformance.com/ Quick Performance]
*[http://www.currieenterprises.com Currie Enterprises]
*[http://www.moserengineering.com Moser Engineering]
*[http://www.tomsdifferentials.com]

==Related resources==
*[http://www.network54.com/Forum/260730/ Ford transmission forum]

[[Category:Good articles]]
[[Category:Rearend]]