Editing Troubleshooting electrical problems

==Basics== Most electrical problems are due to poor connections. Batteries and alternators will go bad in time and should be tested at your local parts store IF the basics mentioned here do not fix the problem. Take both in at once to eliminate further problems. ==Cleaning terminals== Start at the battery. Regardless of how the connections look, remove the cables. Remove the positive cable first, then the negative cable. Use a battery terminal wire brush tool to clean the battery terminals and the cable terminals. Remove all old oxidized contaminants. Be aware that lead is likely present, so wear gloves if you are concerned about lead migrating through your skin. To prevent future corrosion, a light coating of non-conducting grease such as Dow Corning DC4 should be applied. While a professional might not recommend this, I had Japanese mechanics put regular bearing grease on my car battery terminals when I was overseas and it never presented a problem. It seemed to prevent acid build up and corrosion. Remove the other end of the battery cables and clean those terminals and where they mount with a wire brush. Make sure you see shiny bare metal. Again a light coating of non-conducting grease would be optimal, but not mandatory. ===Battery terminals=== [[File:Bad batt clamp term.jpg|thumb|220px|left|Clamp-on replacement battery terminals are to be avoided!]]Do not be tempted to save money by using one (or more) of the cheap, clamp-on style battery cable terminals. Even if they are tight and look fine, all too often they will cause high resistance and can make it seem like the battery is bad, etc. If the terminal fails on a cable there are better terminals that may be used to replace them, or the entire cable can be replaced with a cable having a larger diameter and quality terminals already installed. <br style="clear:both"/> ==Grounding== The battery negative (-) terminal usually mounts to the engine somewhere and often, but not always to the alternator bracket. This makes sure you get the direct connection to the battery which the starter needs since it draws more current than anything else on your car. The battery Positive (+) terminal connects to the starter solenoid. Again, this is due to the demands of the starter. It requires maximum power transfer from the battery. ==Cable inspection== Look your battery cables over very well for signs of problems. Sometimes you will see a green color on the wire somewhere. This is corrosion of the copper and is called verdigris. It is similar to [[rust]] on steel. This is a sign you may need to replace the cable if it can't easily be removed. Even if you can clean it, the corrosion may have traveled up under the insulation and would likely eventually cause problems if it's not already degrading your cable's ability to carry current. Battery cables are cheap. Yes, they can be a pain to change in some instances, but changing them when you can in a controlled environment might save you from being broken down on the road in bad weather. ==Bigger is better== When it comes to battery cables, while the factory cables are "adequate", oftentimes they are replaced with cables that may not be as large in diameter as the originals. In this case, bigger is better. A larger diameter cable can carry more current safely and with less resistance to current flow. While welding cable has been used, the insulation is not ideal for an engine environment. There are, however, other sources of oversized cable that have the proper insulation. Still, a high quality, more than adequate battery cable can be found at most auto parts stores. You should know the length you need before going in. Remove the current cables and take them with you to be sure you have the proper length. You can add a little to the length, but keep in mind, the longer the cable, the more resistance to current flow. ==You're grounded== Be sure there's a ground strap going from the engine to the body and to the frame. Make sure that two grounding straps exist and are also clean at both ends. Most electrical gremlins are due to bad grounds. All too often these bad grounds can be traced to these grounding straps or the battery cables not making a good connection. If all of these connections are good clean connections, you have a solid foundation to build from and will eliminate most electrical gremlins. ==Wiring harness== All too often our cars have had their wiring harness hacked up, cut into, re-routed, and who knows what previous owners of the vehicle did to butcher the factory harness. The wiring in our cars is often in bad shape from age as much as anything else. Wiring insulation was barely adequate decades ago. Add to that the fact that we add on things that demand more than was ever imagined by electrical engineers back in the day. Considering that electrical fires happen all too often and our classics deserve to be protected, a new wiring harness should be considered in most cases. Aftermarket companies are making some very nice kits and some are car or class specific. ==Ignition system== *[[Troubleshooting ignition]] ==Resources== *[http://www.vernco.com/Sparks/id606.htm Voltage drop test] [[Category:Electrical]] [[Category:Troubleshooting]] [[Category:Undeveloped articles]] [[Category:Undeveloped Electrical articles]]

| Editing help (opens in new window)