Editing Basic engine nomenclature

==The "strokes" of an internal combustion 4-stroke engine== From [http://www.answers.com/topic/internal-combustion-engine#Nomenclature Engine nomenclature]: 1. Intake stroke: The first stroke of the internal combustion engine is also known as the suction stroke because the piston moves to the maximum volume position (downward direction in the cylinder). The inlet valve opens as a result of piston movement, and the vaporized fuel mixture enters the combustion chamber. The inlet valve closes at the end of this stroke. 2. Compression stroke: In this stroke, both valves are closed and the piston starts its movement to the minimum volume position (upward direction in the cylinder) and compresses the fuel mixture. During the compression process, pressure, temperature and the density of the fuel mixture increases. 3. Power stroke: When the piston reaches the minimum volume position, the spark plug ignites the fuel mixture and burns. The fuel produces power that is transmitted to the crank shaft mechanism. 4. Exhaust stroke: In the end of the power stroke, the exhaust valve opens. During this stroke, the piston starts its movement in the minimum volume position. The open exhaust valve allows the exhaust gases to escape the cylinder. At the end of this stroke, the exhaust valve closes, the inlet valve opens, and the sequence repeats in the next cycle. Four-stroke engines require two revolutions. ==Other terms== #Cylinder Bore is the Inside Diameter (ID) of the cylinder. #Stroke is the distance a piston moves between Bottom Dead Center (BDC) and Top Dead Center (TDC). #Displacement or Swept Volume is the volume swept by the piston when traveling from BDC to TDC. #Clearance Volume is the volume of the combustion chamber above the piston when it is at TDC. #Piston deck height. This is the dimension from the crown of the piston to the flat deck of the block with the piston at top dead center. Nominally, with a premium 350 piston and a virgin, uncut block, this dimension will be about 0.025". #Squish. This is the dimension from the crown of the piston to the underside of the cylinder head with the piston at top dead center and adding in the thickness of the compressed head gasket. Current thinking is that a squish of 0.035" to 0.045" works best. #Compression height. This is the dimension from the centerline of the piston wrist pin to the top of the piston crown. With a premium piston in a 350 Chevy, this dimension is about 1.560". Lesser quality rebuilder pistons will measure out at around 1.540". This will increase the piston deck height and the squish and make the motor more sensitive to detonation. #Stack. This is the combined dimension of the crankshaft radius, rod length and piston compression height. A common stack with a 350 Chevy would be about 9.003". That would be with a crank radius (half the stroke length of 3.480") of 1.74", rod length of 5.703" and piston compression height of 1.560". #Block deck height. Nominally, this dimension would be about 9.025" on a virgin small block Chevy cylinder block. So, when using a stack of parts equalling 9.003", this would result in a piston deck height of about 0.022". Combined with a steel shim head gasket thickness of about 0.018", this would result in a squish dimension of about 0.040", just in the middle of the desired range of 0.035" to 0.045" to help prevent detonation with a reasonable (nominally, about 10.0:1) static compression ratio on pump gas. Alternately, a builder might cut the block decks down to the height of the stack and use a more conventional composition gasket that specs out at around 0.040" compressed thickness. If you had a stack of 9.003", cut the block decks down to 9.003" and used a 0.040" gasket, then the piston deck height would be 0.000" and the squish would be 0.040". ==Links== *[http://www.motorera.com/dictionary/index.htm Dictionary of Automotive terms] *[[How to rebuild an engine]] *[[Chevrolet engine rebuild guide books and DVDs]] [[Category:Engine]] [[Category:General hotrodding]] [[Category:Undeveloped Engine articles]] [[Category:Undeveloped General hotrodding articles]] [[Category:Undeveloped articles]]

| Editing help (opens in new window)