Camshaft install tips and tricks
(→Mistakes that may "frag" a flat-tappet camshaft and lifters) |
(→Pre-lube engine oil system) |
||
| Line 129: | Line 129: | ||
Used lifters should only be used on the very same cam, in the very same block, and in the very same positions they were removed from. Chances that the lifter bores will be machined on the very same angles on a different block as the block the lifters came out of are about equal to you hitting the lottery. If you purchase a used flat tappet cam from a swap meet or yard sale, plan on using it for a doorstop. New lifters should not be used on an old cam, either. Given the reasonable cost of a new cam and lifter set (~$100 ca. 2012), vs. the cost of cleaning and repairing the damage done by a failed cam and lifters, the choice to use new parts is obvious. | Used lifters should only be used on the very same cam, in the very same block, and in the very same positions they were removed from. Chances that the lifter bores will be machined on the very same angles on a different block as the block the lifters came out of are about equal to you hitting the lottery. If you purchase a used flat tappet cam from a swap meet or yard sale, plan on using it for a doorstop. New lifters should not be used on an old cam, either. Given the reasonable cost of a new cam and lifter set (~$100 ca. 2012), vs. the cost of cleaning and repairing the damage done by a failed cam and lifters, the choice to use new parts is obvious. | ||
| + | Used lifters and a used solid lifter camshaft can be used, it is unfortunate that the cam grinders themselves have published this false wives tale for a very long time. In the order of preference, new camshaft/new lifters, used camshaft/new lifters and then used camshaft/used lifters. It is also preferable that the lifters stay matched to the lobe but if you have mixed them up or sourced them from a different, all is not lost. | ||
| + | |||
| + | Several things must be accomplished to make a used camshaft/used lifter deal work. Each of the lifters will require that you properly polish the bottom of the lifter using a piece of window glass and a new sheet of 600 wet/dry sandpaper. The sandpaper will need to stay lubricated with a light solvent, WD-40 or similar is a good choice. Keep the lifters flat but understand that lifters have a slight convex to them. As you polish them in a figure 8 pattern you should see the center polishing first, if not and the polishing reveals the entire bottom, the lifter is beyond saving. Coloring the bottom of the lifter with a dark color magic marker will help you to see you progress. After polishing, clean all of the lifters thoroughly, several times is best. For the used camshaft, you want to make sure that there are no nicks or injuries to the lobe surfaces. You must also change out your valve springs to the lightest tension possible, not checking springs but something with minimal pressure. Apply Cam lube (Moly) to all surfaces of the lobes and bottoms of lifters - make sure to spend time rubbing the moly into the metal. A motor oil with a high level of ZDP should be used for the initial break-in period, removed after 30-40 minutes of run time and a second dose of the same oil along with a new filter should be used until the first oil change. Also during the initial break-in period, the oil level should be raised one to two quarts to encourage splash lubrication. In some instances a slightly hotter spark plug might be required due to oil fouling. | ||
'''19. Failure to observe the lifters and pushrods turning with the motor running.''' | '''19. Failure to observe the lifters and pushrods turning with the motor running.''' | ||
| Line 252: | Line 255: | ||
While the move has been made by the OEMs to stop using flat tappet cams and lifters in production vehicle engines (replaced by hydraulic roller cams and lifters), they are not immune to failure. | While the move has been made by the OEMs to stop using flat tappet cams and lifters in production vehicle engines (replaced by hydraulic roller cams and lifters), they are not immune to failure. | ||
| − | The same type of oil additives should be used, because it is not just the cam and lifters that require a high pressure lubricant additive; | + | The same type of oil additives should be used, because it is not just the cam and lifters that require a high pressure lubricant additive; use the heavy moly cam break in lube on a roller cam or lifter- it will cure problems. If those are not available for some unknown reason (all should be found online), use motor oil or a roller lifter-specific lube for the roller lifters and cam. |
{| | {| | ||
Your Privacy Choices