Cam and compression ratio compatibility
From Crankshaft Coalition Wiki
m |
(Undo revision 3477941 by 164.90.34.153 (talk)) |
||
| Line 1: | Line 1: | ||
| + | |||
| + | |||
==Matching cam to compression ratio== | ==Matching cam to compression ratio== | ||
Sometimes it's difficult trying to explain to fellows who are new to hot rodding that you have to match the characteristics of the camshaft to the static compression ratio of the motor along with the operating range where the cam makes power. The camshaft is not a stand-alone piece. It must be coordinated with other motor and drivetrain parts in order to arrive at a combination of parts that will all work together toward a common goal. | Sometimes it's difficult trying to explain to fellows who are new to hot rodding that you have to match the characteristics of the camshaft to the static compression ratio of the motor along with the operating range where the cam makes power. The camshaft is not a stand-alone piece. It must be coordinated with other motor and drivetrain parts in order to arrive at a combination of parts that will all work together toward a common goal. | ||
| Line 55: | Line 57: | ||
|- | |- | ||
|} | |} | ||
| − | |||
==Additional reading/engine theory== | ==Additional reading/engine theory== | ||
{{Note1}} | {{Note1}} | ||
| Line 103: | Line 104: | ||
====Dynamic compression ratio calculators==== | ====Dynamic compression ratio calculators==== | ||
| − | *[http://www.empirenet.com/pkelley2/DynamicCR.html | + | *[http://www.empirenet.com/pkelley2/DynamicCR.html Dynamic compression calculator] by Kelly |
| − | *[http://www. | + | *[http://www.uempistons.com/calc.php?action=comp2 Dynamic compression calculator] by KB |
| + | *[http://www.wallaceracing.com/dynamic-cr.php Wallace Racing DCR calculator] | ||
| + | {{Note1}} Some dynamic compression ratio calculators (like KBs) ask for an additional 15 degrees of duration be added to the IVC @ 0.050" lift point nnbfigure. This works OK on older, slower ramped cam lobes, but the faster lobe profiles may need to have 25 degrees or more added to be accurate. | ||
===Cam phasing=== | ===Cam phasing=== | ||
| Line 118: | Line 121: | ||
*[http://www.wallaceracing.com/dynamic-cr.php Wallace Racing DCR calculator] | *[http://www.wallaceracing.com/dynamic-cr.php Wallace Racing DCR calculator] | ||
*[http://www.empirenet.com/pkelley2/DynamicCR.html Kelly DCR calculator] | *[http://www.empirenet.com/pkelley2/DynamicCR.html Kelly DCR calculator] | ||
| − | *[http://www. | + | *[http://www.uempistons.com/calc.php?action=comp2 KB/Silvolite DCR calculator] |
*[http://www.rbracing-rsr.com/comprAdvHD.htm RSR DCR calculator] | *[http://www.rbracing-rsr.com/comprAdvHD.htm RSR DCR calculator] | ||
| + | {{Note1}} Some dynamic compression rtatio calculators (like KBs) ask for an additional 15 degrees of duration be added to the IVC @ 0.050" lift point figure. This works OK on older, slower ramped cam lobes, but the faster lobe profiles may need to have 25 degrees or more added to be accurate. | ||
| + | |||
| + | {{Note1}}If the intake valve closing (IVC) point isn't known, it can be calculated: | ||
| + | # Divide the intake duration by 2 | ||
| + | # Add the results to the lobe separation angle (LSA) | ||
| + | # Subtract any ground-in advance | ||
| + | # Subtract 180 | ||
| + | This result does not need to have any amount added to the IVC point, like the KB calculator calls for. | ||
| + | |||
| + | ==Compression ratio calculators== | ||
| + | ===Static CR=== | ||
| + | *[http://www.wheelspin.net/calc/calc2.html SCR] | ||
| + | |||
| + | ===Dynamic CR=== | ||
| + | *[http://www.empirenet.com/pkelley2/DynamicCR.html Dynamic compression calculator] by Kelly | ||
| + | *[http://www.uempistons.com/calc.php?action=comp2 Dynamic compression calculator] by KB | ||
| + | *[http://www.wallaceracing.com/dynamic-cr.php Wallace Racing DCR calculator] | ||
| + | *[http://www.rbracing-rsr.com/comprAdvHD.htm RSR DCR calculator] | ||
| + | {{Note1}} Some dynamic compression ratio calculators (like KBs) ask for an additional 15 degrees of duration be added to the IVC @ 0.050" lift point figure. This works OK on older, slower ramped cam lobes, but the faster lobe profiles may need to have 25 degrees or more added to be accurate.<br> | ||
| + | |||
| + | {{Note1}}If the intake valve closing (IVC) point isn't known, it can be calculated: | ||
| + | # Divide the intake duration by 2 | ||
| + | # Add the results to the lobe separation angle (LSA) | ||
| + | # Subtract any ground-in advance | ||
| + | # Subtract 180 | ||
===Static compression ratio=== | ===Static compression ratio=== | ||
| Line 134: | Line 162: | ||
[[Category:Camshaft]] | [[Category:Camshaft]] | ||
| + | <pre style="border:none;"> | ||
General Application Chart * | General Application Chart * | ||
Advertised | Advertised | ||
| Line 149: | Line 178: | ||
290°+ 3.73+ 3400-8000 | 290°+ 3.73+ 3400-8000 | ||
10.5 to 12 3500+ | 10.5 to 12 3500+ | ||
| + | </pre> | ||
Your Privacy Choices