|
|
| Line 1: |
Line 1: |
| − | {{Youcanedit}}
| |
| | | | |
| − | ==Summary==
| |
| − | John Deere Blitz Black is enamel paint manufactured by Valspar Paint for John Deere, for the purpose of painting tractors and farm equipment. Although re-branded for John Deere, Blitz Black comes from the Valspar BPS Agricultural Restoration Series Tractor & Implement product line. It's popular among hotrodders for the following reasons:
| |
| − | *It's inexpensive.
| |
| − | *It has a reputation for extreme durability.
| |
| − | *It provides the look of a primered "rat" or "traditional" hot rod (described as: "flat clear", "suede", "satin", or "semi-gloss").
| |
| − | *It's easy to touch up.
| |
| − |
| |
| − | Although John Deere Blitz Black paint can be applied with typical paint equipment, John Deere recommends using their own primer and reducer. The paint and the primer are typically $25 dollars for a gallon, and the reducer is about $15 for a quart. JDBB products also come in spray cans.
| |
| − |
| |
| − | ==Application==
| |
| − | #If the existing paint isn't peeling, or doesn't have large amounts of rust, then no primer is necessary. Sand with extra fine grit sand paper, wipe with a clean cloth, and then apply JDBB paint.
| |
| − | #For spraying with an HVLP gun, use a 1.4 or 1.5 tip.
| |
| − | #If a primer is needed, JDBB primer is recommended (it's available in spray cans, quarts, and gallons). Wait 36 hours after applying primer to apply paint.
| |
| − | #John Deere thinner is needed, at a mix ratio of 8 parts JDBB paint:1 part John Deere thinner.
| |
| − | #For faster-drying and harder paint, John Deere hardener can be used. It's available in pints. When using the hardener, the mix ratio is 8 parts JDBB paint:1 part John Deere thinner:1 part John Deere hardener.
| |
| − | #Spray one light tack coat, wait 10-15 minutes, and shoot the full wet coat.
| |
| − | #Wait no longer than 3 hours to apply a second coat. However, one coat with the 8:1:1 paint-thinner-hardener ratio should be adequate.
| |
| − | #A gallon will easily cover a small car.
| |
| − |
| |
| − | ==Notes==
| |
| − | *Be wary of striping, thought to be caused by the reducer drying too fast. To eliminate striping, some people recommend using regular enamel reducer instead of the John Deere reducer, for a slower evaporation rate.
| |
| − | *Hold the gun at a 90 degree angle to the surface, and keep a 50% overlap.
| |
| − | *John Deere Blitz Black paint can't be applied to high heat areas such as engine blocks, headers, or pipes. And, it will not retard rust.
| |
| − | *Some people report success applying it to fiberglass.
| |
| − | *Urethane primer or epoxy primer may also be viable as undercoats for JDBB paint.
| |
| − | *Some say that JDBB paint is subject to fading and chalking over the years.
| |
| − | *According to John Deere, yes, you can paint over JDBB paint with another coat of primer and/or enamel paint.
| |
| − | *Opinions are mixed on using a clearcoat over JDBB. Some say that it can be applied if a flattening agent is used. For a glossy look, wet sanding and buffing are recommended.
| |
| − |
| |
| − | ==Part numbers==
| |
| − | Part numbers may vary for different regions. California has been specifically mentioned as a place where JDBB may be difficult to obtain, or may be sold under a different part number.
| |
| − |
| |
| − | *John Deere Blitz Black paint: TY-25669 (formerly TY-6416)
| |
| − | *John Deere Primer: TY6457
| |
| − | *John Deere Reducer: PT158
| |
| − | *John Deere Hardener: REN3001
| |
| − |
| |
| − | ==Where to get John Deere Blitz Black paint==
| |
| − | *[http://dealerlocator.deere.com/servlet/DealerLocator?command=home&locator=3&selectLocale=en_US&sessionId=Rgf865DJYGDkmUUhinR1QMN John Deere dealer locator]
| |
Your Privacy Choices