Determining top dead center
From Crankshaft Coalition Wiki
(Add link, text, image; minor clean up; format) |
|||
| Line 29: | Line 29: | ||
==Rebuilt dampers== | ==Rebuilt dampers== | ||
| − | One noted place to buy a rebuilt damper/balancer is [http://www.damperdoctor.com/ Damper Doctor]. They disassemble stock, OEM production dampers, clock the hub to the ring and reassemble the unit with new elastomeric material pressed together under tremendous hydraulic pressure. An 8" damper for a 350 Chevy can be had for a mere $32.95 (ca. 2012) | + | One noted place to buy a rebuilt damper/balancer is [http://www.damperdoctor.com/ Damper Doctor]. They disassemble stock, OEM production dampers, clock the hub to the inertia ring and reassemble the unit with new elastomeric material pressed together under tremendous hydraulic pressure. An 8" damper for a 350 Chevy can be had for a mere $32.95 (ca. 2012). |
| − | The option is a used damper/balancer that may be clocked worse than the one you have or an aftermarket damper/balancer that will cost more money and may not have been correctly machined on the inner hub diameter. Some of these Chinese dampers being sold are either oversize or undersize for the production crank snout diameter. The damper/balancer MUST BE A SNUG PRESS-FIT on the crank in order to properly transfer harmonics from the crankshaft to the damper/balancer hub. | + | The option is a used damper/balancer that may be clocked worse than the one you have or an aftermarket damper/balancer that will cost more money and may not have been correctly machined on the inner hub diameter. Some of these offshore (Chinese) dampers being sold are bored either oversize or undersize for the production crank snout diameter. The damper/balancer hub MUST BE A SNUG PRESS-FIT on the crank in order to properly transfer harmonics from the crankshaft to the damper/balancer hub and on to the inertia ring, where harmonics are dissipated. |
| − | On a street engine or a drag race engine down to 11.00 E.T. in the quarter mile, an OEM-type damper/balancer may be used legally. At 10.99 E.T., an aftermarket SFI-18.1 damper/balancer is required. | + | On a street engine or a drag race engine down to 11.00 E.T. in the quarter mile, an OEM-type damper/balancer may be used legally. At 10.99 E.T. and quicker, an aftermarket SFI-18.1 damper/balancer is required. Blower motors normally do not use a balancer/damper, but instead, use an aluminum toothed hub on the crank snout to drive the blower. On these blown motors, the large Gilmer drive belt functions as a dampener to dissipate crankshaft harmonics. |
===Damper suppliers=== | ===Damper suppliers=== | ||
| Line 56: | Line 56: | ||
If the engine is a short block on the stand, you can determine TDC with a simple homemade piston stop made from a strap of metal bolted across two head bolt holes, with the strap drilled and tapped for an adjustable bolt/nut assembly. A dial indicator can also be used on a fixture that bridges the bore or on a magnetic base. This would be an ideal time to note the piston-to-deck clearance for use in computing the static compression ratio and quench distance. | If the engine is a short block on the stand, you can determine TDC with a simple homemade piston stop made from a strap of metal bolted across two head bolt holes, with the strap drilled and tapped for an adjustable bolt/nut assembly. A dial indicator can also be used on a fixture that bridges the bore or on a magnetic base. This would be an ideal time to note the piston-to-deck clearance for use in computing the static compression ratio and quench distance. | ||
| − | If the engine | + | If the engine has the heads on, use a spark plug-type piston stop tool. If there is a timing tab present, use it to mark the position with. If no tab, use a length of stiff wire that's attached to the engine to use to show the positions. This may be made easier by using a degree wheel or a timing tape on the outer ring of the damper. |
| + | #Set the plug hole-mounted piston stop to contact the piston close to TDC | ||
| + | #Rotate engine until the stop just contacts the piston- mark the location | ||
| + | #Then rotate in the opposite direction until the piston is stopped | ||
| + | #Half way between the two marks is approximately TDC | ||
| + | |||
[[File:TDC1.jpg |thumb|left|Strap-type and spark plug-type piston stop tools]] | [[File:TDC1.jpg |thumb|left|Strap-type and spark plug-type piston stop tools]] | ||
<br style="clear: both" /> | <br style="clear: both" /> | ||
| Line 132: | Line 137: | ||
If using a camshaft with more duration, you may want to increase the ignition timing lead at the crank and limit the centrifugal advance in the distributor to achieve your total ignition timing. Some distributors, like those sold by MSD, use different bushings to control the ''amount'' of mechanical advance. The '''rate''' of mechanical advance is tailored by changing the springs and/or centrifugal weights. Usually just spring changes are all that is needed. If working on a GM HEI, the original weights are almost always a better choice than the weights sold in the various advance curve kits available from Mr. Gasket, Crane, Summit, Moroso, etc. | If using a camshaft with more duration, you may want to increase the ignition timing lead at the crank and limit the centrifugal advance in the distributor to achieve your total ignition timing. Some distributors, like those sold by MSD, use different bushings to control the ''amount'' of mechanical advance. The '''rate''' of mechanical advance is tailored by changing the springs and/or centrifugal weights. Usually just spring changes are all that is needed. If working on a GM HEI, the original weights are almost always a better choice than the weights sold in the various advance curve kits available from Mr. Gasket, Crane, Summit, Moroso, etc. | ||
| − | If you are using a radical cam and/or a converter that allows the engine RPM to come up past where you would normally limit centrifugal advance (about 2800 rpm), you may want to modify the distributor so that centrifugal advance is locked out and put your total amount of ignition advance in at the crank. Of course, the engine will not want to crank against this much ignition lead, so you will want to install a momentary switch in the wire going to the "+" terminal of the coil to disable the coil while you crank the engine. Once the engine is spinning, release the switch and the engine will fire normally. | + | If you are using a radical cam and/or a converter that allows the engine RPM to come up past where you would normally limit centrifugal advance (about 2800 rpm), you may want to modify the distributor so that centrifugal advance is locked out and put your total amount of ignition advance in at the crank. Of course, the engine will not want to crank against this much ignition lead, so you will want to install a momentary switch in the wire going to the "+" terminal of the coil to disable the coil while you crank the engine. Once the engine is spinning, release the switch and the engine will fire normally. |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
Your Privacy Choices