Hi-torque starter
From Crankshaft Coalition Wiki
Metzijndrie (Talk | contribs) |
|||
| Line 1: | Line 1: | ||
| − | [[Image:3 okt 2008 hi-tork starter 001.jpg]] | + | |
| + | ==Introduction== | ||
| + | "Hi-torque" starters can mean a starter made with a gear reduction to add mechanical advantage, or it can mean a starter wound with an armature that delivers more torque than a "standard" starter. | ||
| + | |||
| + | ==OEM high torque starters== | ||
| + | Two part numbers for OEM starters from [http://www.sallee-chevrolet.com/Starters_And_Parts/index.cfm Sallee Chevrolet GMPP parts] are: | ||
| + | |||
| + | '''10455709'''- Gear reduction (GR) starter, as used on the 1988-'95 L-98 Corvette. | ||
| + | Technical Notes: Use with 12-3/4” outside diameter flywheel. Pre-LT1 engines require starter machine work. | ||
| + | |||
| + | [[File:10455702gm GR starter.jpg|thumb|left|400px|Part number 10455709 gear reduction starter for the 153 tooth flexplate/flywheel]] <br style="clear:both"/> | ||
| + | |||
| + | |||
| + | '''10465143'''- originally for Camaro Z28 with LT1 engine, so it would also have been pre-L31 Vortec era. The Sallee description calls it a GR starter, but it doesn't look like a GR starter, and [http://www.summitracing.com/parts/NAL-10465143 Summit] calls it an "inline" starter, as well- so the description may be wrong. | ||
| + | [[File:10465293 gm starter inline.jpg|thumb|left|400px|Part number 10465143 starter for the 153 tooth flexplate/flywheel]] <br style="clear:both"/> | ||
| + | |||
| + | It looks more like the small diameter permanent magnet starters that came around in the '90s. Costs about $350 from Summit as of mid-2012, no warranty, and it's listed some places as a reman, but this hasn't been verified. A better deal could likely be found elsewhere- like from a 'yard. | ||
| + | |||
| + | ==Aftermarket high torque starters== | ||
| + | [[Image:3 okt 2008 hi-tork starter 001.jpg|thumb|400px|Hi torque starter; Ford '67 289 /AT]] | ||
| + | |||
| + | High torque starters are generally used on high performance engines. They are better at cranking over a high compression engine. They are usually less prone to heat soak. Most also have universal mounting so they can be used with different flywheel sizes, and they may have a feature that allows the solenoid to be "clocked" into a position that gives the best clearance. | ||
| + | |||
| + | High Torque Starter Repairs | ||
| + | |||
| + | Most aftermarket high torque starters are originally Japanese manufactured. While China has copied these and supplies a number of starter "sellers" with their own name branded units, in general the starters all feature the same basic construction. | ||
| + | |||
| + | Most of the failures related to these starters involves damage to the pinion gear. Replacement pinion gears can be obtained and the starter disassembled, the gear replaced, the starter reassembled and placed back in service. Most starters will have the 9 tooth pinion gear although a few will have 14 tooth pinions. | ||
| + | |||
| + | Replacement of the Pinion Gear: | ||
| + | |||
| + | *With the starter on the bench, first use a paint marker to provide alignment marks on the main motor housing and the gear housing. | ||
| + | *Remove the three bolts holding the starter to the aluminum mounting block. For ease of re-installation, marking the clocking of the starter motor is suggested. | ||
| + | e reverse order of the disassembly. | ||
| + | *Pay close attention to the orientation of the solenoid actuator as it must go back in the proper way. | ||
Your Privacy Choices