Make a fiberglass fan shroud
(→Shaping the foam) |
|||
| Line 73: | Line 73: | ||
[[Image:20wax and PVA.JPG|center|600px]] | [[Image:20wax and PVA.JPG|center|600px]] | ||
| + | |||
| + | [[Image:21mat strips.JPG|center|600px]] | ||
| + | |||
| + | [[Image:22wetting out strips.JPG|center|600px]] | ||
| + | |||
| + | [[Image:23wetting out some more.JPG|center|600px]] | ||
| + | [[Image:24wetting surface.JPG|center|600px]] | ||
| + | [[Image:25wetting out buck.JPG|center|600px]] | ||
| + | |||
| + | [[Image:26applying material.JPG|center|600px]] | ||
| + | |||
| + | [[Image:27more applying material.JPG|center|600px]] | ||
| + | |||
| + | [[Image:28stretching over corner.JPG|center|600px]] | ||
| + | |||
| + | [[Image:Even 29more applying material.JPG|center|600px]] | ||
| + | |||
| + | [[Image:30rolling out the air.JPG|center|600px]] | ||
| + | |||
| + | [[Image:31rolling out some more air.JPG|center|600px]] | ||
| + | [[Image:32dwell in the corners.JPG|center|600px]] | ||
| + | |||
| + | [[Image:33rolling over the apex of the radius.JPG|center|600px]] | ||
| + | |||
| + | [[Image:34all air is rolled out.JPG|center|600px]] | ||
| + | |||
| + | [[Image:35rolled out.JPG|center|600px]] | ||
| + | |||
| + | [[Image:36corner detail.JPG|center|600px]] | ||
| + | |||
| + | [[Image:37sizing up some mat.JPG|center|600px]] | ||
| + | |||
| + | [[Image:38more wetting it out.JPG|center|600px]] | ||
| + | |||
| + | [[Image:39resin in the sun shiney light.JPG|center|600px]] | ||
| + | |||
| + | [[Image:40all laid up.JPG|center|600px]] | ||
| + | |||
| + | [[Image:41slightly stressed from shrinking too fast.JPG|center|600px]] | ||
| + | |||
| + | [[Image:42close up of resin rich and air bubbles.JPG|center|600px]] | ||
| + | |||
| + | [[Image:43resin rich.JPG|center|600px]] | ||
| + | |||
| + | [[Image:44good resin glass ratio.JPG|center|600px]] | ||
| + | |||
| + | [[Image:44trimming the excess.JPG|center|600px]] | ||
| + | |||
| + | [[Image:45trimmed part.JPG|center|600px]] | ||
| + | |||
| + | [[Image:46trimmed part with a fat boy.JPG|center|600px]] | ||
| + | |||
| + | [[Image:47skim coat of bondo.JPG|center|600px]] | ||
| + | |||
| + | [[Image:48more bondo.JPG|center|600px]] | ||
| + | |||
| + | [[Image:49even more bondo.JPG|center|600px]] | ||
| + | |||
| + | [[Image:50after sanding.JPG|center|600px]] | ||
| + | |||
| + | [[Image:51after more sanding.JPG|center|600px]] | ||
| + | |||
| + | [[Image:52chipping out rocks.JPG|center|600px]] | ||
| + | |||
| + | [[Image:53most of the foam out.JPG|center|600px]] | ||
| + | |||
| + | [[Image:55nice and clean.JPG|center|600px]] | ||
| + | [[Image:56clean inside and out.JPG|center|600px]] | ||
| + | |||
| + | [[Image:57it is hollow.JPG|center|600px]] | ||
| + | |||
| + | [[Image:58tape off the table.JPG|center|600px]] | ||
| + | |||
| + | [[Image:59lay up the return.JPG|center|600px]] | ||
| + | |||
| + | [[Image:60pull the part.JPG|center|600px]] | ||
| + | |||
| + | [[Image:61return.JPG|center|600px]] | ||
| + | |||
| + | [[Image:62finished part.JPG|center|600px]] | ||
| + | |||
| + | [[Image:64backside.JPG|center|600px]] | ||
| + | |||
| + | [[Image:65ready to prime.JPG|center|600px]] | ||
| + | |||
| + | [[Image:66rack for priming.JPG|center|600px]] | ||
| + | |||
| + | [[Image:67duratec.JPG|center|600px]] | ||
| + | |||
| + | [[Image:68this primer has some solids.JPG|center|600px]] | ||
| + | |||
| + | [[Image:Spraying primer.JPG|center|600px]] | ||
| + | |||
| + | [[Image:Primered part.JPG|center|600px]] | ||
Your Privacy Choices