Intake manifold/cylinder head internal vacuum leak

Occasionally, you may experience a vacuum leak into the intake ports from the crankcase of the motor due to the intake manifold / cylinder head interface not being machined parallel. Here, I'm talking about looking at the manifold from an end view, from the front or rear of the car for instance. Unless you're using all brand new parts, you have no way of knowing if the heads or manifold have been machined by the previous owner, so the interface at the manifold/head could be out of parallel. In other words, the gasket might be pinched tightly at the top of the port and sealing fine, but might be wide open to the crankcase at the bottom of the port. The manifold may also be warped a little. No amount of propane or carburetor cleaner will find such a leak. The best way is to insure the elimination of such a problem while building the motor.

Occasionally, you may experience a vacuum leak into the intake ports from the crankcase of the motor due to the intake manifold / cylinder head interface not being machined parallel. Here, I'm talking about looking at the manifold from an end view, from the front or rear of the car for instance. Unless you're using all brand new parts, you have no way of knowing if the heads or manifold have been machined by the previous owner, so the interface at the manifold/head could be out of parallel. In other words, the gasket might be pinched tightly at the top of the port and sealing fine, but might be wide open to the crankcase at the bottom of the port. The manifold may also be warped a little. No amount of propane or carburetor cleaner will find such a leak. The best way is to insure the elimination of such a problem while building the motor.

Here's how I set up the intake manifold/cylinder head interface to prevent vacuum leaks from the crankcase to the head ports....Begin with the heads properly torqued to the block for the final time and ready to go. Measure the thickness of your new intake manifold gaskets. Get flat washers or shims that will measure that thickness. With the manifold off and the mating surface on the cylinder heads de-greased, put a dab of RTV on the washers/shims and stick them on each corner bolt hole on the cylinder heads. Let the RTV set up. Stuff paper towels into the ports to keep debris out. Make up 16 pea-sized balls of modeling clay. (Use oil-based modeling clay from a craft store, not Play-Doh). De-grease the intake manifold at the ports. Place the balls of clay on the top and bottom of each port of the manifold, squishing them down well so they stay in place. You want them to be thicker than the shims/washers that are RTV'd to the heads. With your fingers, coat a little oil on the heads where the clay will meet the heads to keep it from sticking to the heads. Now carefully place the manifold into place on the heads and use bolts on the four corners to just snug the manifold down until you feel resistance against the shims/washers. Remove the manifold carefully. Cut half the clay away at each position with your pocket knife. Measure the thickness of the remaining clay at all 16 positions with the depth function end of your 6" dial caliper. You'll know pretty quickly if the manifold/head interface is square. Record the measurements on the manifold with a permanent marker like a Sharpie. The widest measurement will be the standard to which you will want your machinist to cut the other positions on the manifold to make it square with the heads, thusly sealing up the motor.

Here's how I set up the intake manifold/cylinder head interface to prevent vacuum leaks from the crankcase to the head ports....Begin with the heads properly torqued to the block for the final time and ready to go. Measure the thickness of your new intake manifold gaskets. Get flat washers or shims that will measure that thickness. With the manifold off and the mating surface on the cylinder heads de-greased, put a dab of RTV on the washers/shims and stick them on each corner bolt hole on the cylinder heads. Let the RTV set up. Stuff paper towels into the ports to keep debris out. Make up 16 pea-sized balls of modeling clay. (Use oil-based modeling clay from a craft store, not Play-Doh). De-grease the intake manifold at the ports. Place the balls of clay on the top and bottom of each port of the manifold, squishing them down well so they stay in place. You want them to be thicker than the shims/washers that are RTV'd to the heads. With your fingers, coat a little oil on the heads where the clay will meet the heads to keep it from sticking to the heads. Now carefully place the manifold into place on the heads and use bolts on the four corners to just snug the manifold down until you feel resistance against the shims/washers. Remove the manifold carefully. Cut half the clay away at each position with your pocket knife. Measure the thickness of the remaining clay at all 16 positions with the depth function end of your 6" dial caliper. You'll know pretty quickly if the manifold/head interface is square. Record the measurements on the manifold with a permanent marker like a Sharpie. The widest measurement will be the standard to which you will want your machinist to cut the other positions on the manifold to make it square with the heads, thusly sealing up the motor.

--------------------------------------------------------------------------------

--------------------------------------------------------------------------------