383/388 Chevy stroker
m (Reverted edits by 170.185.71.19 (talk) to last revision by Cobalt327) |
|||
| Line 11: | Line 11: | ||
When the various parts that make up the reciprocating assembly are selected, these parts have to fit into the SBC deck height dimension of ~9.025". When calculating the stack of parts that make up the reciprocating assembly, use the radius of the stroke, which is the same thing as 1/2 of the stroke, because only 1/2 of the crankshaft stroke swings ''above'' the crankshaft centerline. So for a stock 350 Chevy having a stroke of 3.48", use 1/2 of the stroke (3.480" times .5 = 1.74") to start putting the stack of parts together that will fit into the block. | When the various parts that make up the reciprocating assembly are selected, these parts have to fit into the SBC deck height dimension of ~9.025". When calculating the stack of parts that make up the reciprocating assembly, use the radius of the stroke, which is the same thing as 1/2 of the stroke, because only 1/2 of the crankshaft stroke swings ''above'' the crankshaft centerline. So for a stock 350 Chevy having a stroke of 3.48", use 1/2 of the stroke (3.480" times .5 = 1.74") to start putting the stack of parts together that will fit into the block. | ||
| − | In a running engine, the oil clearance will create a slightly longer stack- a 0.003" rod bearing oil clearance will add something slightly less than 0.003". In this article, oil clearance will NOT be added into the stack height. If desired the oil clearance may be added; easiest way to do this would be to either add the oil clearance to the rod length, or simpler yet, just add the oil clearance after the stack height is calculated. The added height from the oil clearance would only be an issue if the engine is being built with a marginal amount of quench (<0.035" for steel rods); if built with the "ideal" 0.040" quench, the oil clearance can be basically | + | In a running engine, the oil clearance will create a slightly longer stack- a 0.003" rod bearing oil clearance will add something slightly less than 0.003". In this article, oil clearance will NOT be added into the stack height. If desired the oil clearance may be added; easiest way to do this would be to either add the oil clearance to the rod length, or simpler yet, just add the oil clearance after the stack height is calculated. The added height from the oil clearance would only be an issue if the engine is being built with a marginal amount of quench (<0.035" for steel rods); if built with the "ideal" 0.040" quench, the oil clearance can be basically ignored. |
| + | |||
===Piston rock=== | ===Piston rock=== | ||
Another consideration is piston "rock". At TDC as the piston transitions from upward to downward movement, the piston will tip on its wrist pin. This causes one edge of the piston to be a small amount higher than the other edge. The exact amount will vary with how much piston to wall clearance there is; more clearance means more piston rock. Forged pistons generally have a looser piston to wall clearance than cast pistons, but newer design forged pistons have tighter clearances than was used in days gone by. This is another thing that's basically accounted for if a 0.040" quench distance is maintained. Only if less than 0.035" would this possible be an issue. | Another consideration is piston "rock". At TDC as the piston transitions from upward to downward movement, the piston will tip on its wrist pin. This causes one edge of the piston to be a small amount higher than the other edge. The exact amount will vary with how much piston to wall clearance there is; more clearance means more piston rock. Forged pistons generally have a looser piston to wall clearance than cast pistons, but newer design forged pistons have tighter clearances than was used in days gone by. This is another thing that's basically accounted for if a 0.040" quench distance is maintained. Only if less than 0.035" would this possible be an issue. | ||
Your Privacy Choices