|
|
| Line 1: |
Line 1: |
| − | {{youcanedit}} | + | {{needspics}} |
| | | | |
| | ==Cheapo paint job== | | ==Cheapo paint job== |
| − | Paint is expensive, and learning how to paint your car takes practice, patience, and several screw-ups before you get it right. | + | Paint is expensive, and learning how to paint your car takes practice, patience, and several screw-ups before you get it right. |
| | | | |
| | Faced with the financial obstacle and the learning curve, many hotrodders are tempted to opt for a "cheapo" paint job. The two biggest temptations in the "cheapo paint job" realm seem to be an inexpensive (and questionably professional) paint shop (ie: Maaco), or a cheaper, easier, and ostensibly more forgiving product line (ie: DupliColor). | | Faced with the financial obstacle and the learning curve, many hotrodders are tempted to opt for a "cheapo" paint job. The two biggest temptations in the "cheapo paint job" realm seem to be an inexpensive (and questionably professional) paint shop (ie: Maaco), or a cheaper, easier, and ostensibly more forgiving product line (ie: DupliColor). |
| Line 14: |
Line 14: |
| | For a full explanation of why, in most cases, a cheapo paint job is a bad idea (and, suggestions for when it's '''not''' a bad idea), see [[Cheapo paint job]]. | | For a full explanation of why, in most cases, a cheapo paint job is a bad idea (and, suggestions for when it's '''not''' a bad idea), see [[Cheapo paint job]]. |
| | | | |
| − | Last but not least, these materials can do major harm to your health if you do not closely follow the manufacturers recommendations for skin and lung protection. Appropriate respirators must be used!
| + | ==General tips, tricks, and techniques== |
| | + | *See [[Body and exterior tips]] |
| | + | *See [[Health and safety in the shop or garage]] |
| | | | |
| − | == General Tips, Tricks, and Techniques == | + | *A 12" aluminum ruler works great for ratios example: 4:1:1 = 4" :1" :1". Stir your paint with it and wipe it off so you can reuse it later, you can find them everywhere for $1. |
| | | | |
| | + | *Save your old reducer gallon cans and quart size hardener cans. With a pair of tin snips, cut the tops off (at the bead), and use them for mixing paint with a ruler -- but run some tape around the edge so you don't cut yourself. |
| | | | |
| − | '''Temperature, Temperature, Temperature...'''
| + | *When opening a can of paint, punch a few holes in the trough where the lid sits with a hammer and nail. That way, excess paint will drain out of the trough and into the can, rather than splattering when placing the lid back on the can. |
| | | | |
| − | Warm and dry conditions are ideal for spray painting. The ambient temperature range for spraying most modern paints is about 65-90 degrees Fahrenheit. Be sure to choose the hardeners and reducers for the temperature range you'll be working in. Aerosols don't always work best in the damp and colder temperatures, which can hinder drying time, although it can be done. If it's not warm and dry outside, work in a well-ventilated garage, but set it up for painting.
| + | *Buy a set of inexpensive spatulas to use as scrapers for paint cans. |
| | | | |
| − | Try to keep your gun straight not angled to far up or too far down. Keep the gun about 5 to 6 inches from the surface the whole time or you will have heavy painted surfaces and lightly painted surfaces. Practice spray technique on an old fender to determine proper gun adjustment, pass speed, and pass overlap.
| + | *To preserve hardener, displace the air in the can with inert gas, such as the shield gas (CO2/argon, etc.) from a MIG welder. Or, use a commercial inert gas finish preservative such as [http://www.bloxygen.com/ Bloxygen]. |
| | + | {{Warning}}DO NOT use oxygen or acetylene from a torch! |
| | | | |
| − | '''How to make your own temporary paint booth'''
| + | *For easier pouring, affix a 2-inch piece of masking tape to the edge of a large gallon of paint. Pour the paint over the piece of tape. |
| | | | |
| − | Painting in a garage lessens the chance of bugs or dust ending up lodged in your paint while it is still in its curing stage.
| + | *Use a ladle for handling paint. |
| − |
| + | |
| − | One way to turn your garage into a temporary paint booth is to get huge plastic drop cloths from you local hardware store or home improvement store. They are cheap and effective for protecting your tool boxes and "toys" (Atv's, etc.) from over spray.
| + | |
| − | Open up your garage door about 1/8 to a 1/4 way up, this will help with ventilation, since solvents sink to the floor. Place a fan near the opening, facing outside, to help even more with airflow. Opening any side doors and roof vents helps lots too, Place another fan around here. Box fans may work, but at a minimum you should ensure that these fans are the brushless type to reduce the amount of sparking the exhaust stream will "see". Remember, the fewer sparks the paint vapor "sees" the less likely you are to cause an explosion. An even better solution to box fans would be to use squirrel cage blowers, commonly found in HVAC and exhaust vent systems. Try to get the type where the motor is outside of the squirrel cage to reduce heating the exhaust stream. Place the squirrel cage blower motor outside of your "paint booth" and run ducting into (or out of) your paint booth. A good rule of thumb for blower sizing is to try to change the air TWICE every minute. Hence, if you have a 10'x10'x10' paint booth (1000 cubic feet) you want a 2000 cfm blower (2000 cubic feet per minute).
| + | |
| − |
| + | |
| | | | |
| − | Something that will help keep dust and bugs from coming into your garage is to buy a furnace filter the same size as the window
| + | *When purchasing new paint or other finishing products, write the date on them with a black magic marker. |
| − | (or build a frame for the filters to go over your door)that you have open. This will collect the dirt and bugs that want to invade what you're doing.
| + | |
| − | If there are strict rules in your area, something that will help is to place a filter before your fan so that it filters the air as it is leaving your shop.
| + | |
| − |
| + | |
| − | '''Basic mixing techniques'''
| + | |
| | | | |
| − | Paint and related finishing products can be mixed in glass measuring cups, medicine cups, soup cans, or shot glasses. However, EZ Mix cups are generally preferred for ease of use. Containers with measurements marked on the side are generally most useful. Paper cups are cautioned against because some may have a wax coating. Similarly, plastic cups or containers (medicine cups, yogurt containers, cleaned bottle caps, etc.) are also cautioned against. There are many different kinds of plastic, some of which are inappropriate for storing certain types of finishing products.
| + | *For stirring paint, use inexpensive "jumbo sticks", tongue depressors, Popsicle sticks, wood sticks, or butter knives. |
| − | When mixing double portions of paint or primer, mix one portion at a time. For example,''''' 8:2:1''''' is easier to keep track of than '''''16:4:2'''''. Most, if not all, automotive paint has the correct ratio for the paint/thinner/hardener printed on the label. If not, consult your favorite body man for the best ratio to use on your paint.
| + | |
| | | | |
| − | After mixing each individual portion, add the two portions together and mix well again. This also cuts down on wasted material if you make a mistake (too much hardener, wrong reducer, etc.).
| + | *Paint stirring sticks with marks for different mix ratios can be useful for mixing paint. |
| − | | + | |
| − | ''TOO HELP YOU ALONG THE WAY''
| + | |
| − | | + | |
| − | GREAT TIP '''When opening a can of paint, punch a few holes in the trough where the lid sits with a hammer and nail. That way, excess paint will drain out of the trough and into the can, rather than splattering when placing the lid back on the can.'''
| + | |
| − | -Buy a set of inexpensive spatulas to use as scrapers for paint cans.
| + | |
| − | | + | |
| − | -To preserve hardener, displace the air in the can with inert gas, such as the shield gas (CO2/argon, etc.) from a MIG welder (DO NOT USE O2 OR ACETALINE FROM A GAS WELDING UNIT). Or, use a commercial inert gas finish preservative such as Bloxygen.
| + | |
| | | | |
| − | -For easier pouring, affix a 2-inch piece of masking tape to the edge of a large gallon of paint. Pour the paint over the piece of tape.
| + | *When opening a gallon of paint that isn't all going to be used immediately, mix it very well and pour it off into quart cans. You can get empty quart cans from a local (private, not chain-store) paint shop for cheap or free. While pouring, intermix the paint; pour a little bit into each can at a time. |
| − | | + | |
| − | -Use a ladle for handling paint.
| + | |
| − | | + | |
| − | -When purchasing new paint or other finishing products, write the date on them with a black magic marker. | + | |
| − | | + | |
| − | -For stirring paint, use inexpensive "jumbo sticks", tongue depressors, Popsicle sticks, wood sticks, or butter knives.
| + | |
| − | | + | |
| − | GREAT TIP '''Paint stirring sticks with marks for different mix ratios can be useful for mixing paint.'''
| + | |
| | | | |
| − | When opening a gallon of paint that isn't all going to be used immediately, mix it very well and pour it off into quart cans. You can get empty quart cans from a local (private, not chain-store) paint shop for cheap or free.
| + | *Leftover paint with hardener can be placed in the refrigerator. The cold temperature will slow down the hardener. You can even throw you spray gun in there if you find you need some supplies, and you are in the middle of painting. |
| − | While pouring, intermix the paint; pour a little bit into each can at a time.
| + | |
| − |
| + | |
| − | GREAT TIP '''Leftover paint with hardener can be placed in the refrigerator. The cold temperature will slow down the hardener., you can even throw you spray gun in there if you find you need some supplies, and you are in the middle of painting!'''
| + | |
| | | | |
| − | ==Proper Paint Clothing==
| + | *It pays to completely blow off the whole car inside and out with compressed air before you begin painting. Wear eye protection and a respirator. |
| − | When painting it is always a good idea to wear some kind of protective clothing it not only helps keep you from contacting the toxic materials but it also will help keep unwanted materials from getting on your paint job. The first and most important is a paint mask made for '''automotive''' refinishing there are a lot of companies that sell these. Get a paint suit or use a lint free pair of coveralls. The next thing is a pair of gloves, latex style; I have found that the nitrile gloves hold up better to the chemicals. Do not use a set of rubber gloves they are too clumsy and you need the motion that you get from the latex style gloves. Get some kind of lint free head cover, this keeps your hair on your head and not on the job you are working on. They also recommend a foot cover (which I never used) but they look like a sock for your shoes.
| + | |
| − | There are many different companies that these items can be purchased, local stores and Internet. The most important item that you need is a paint mask. You can get by with out the other items (with extra buffing when you are done) but the '''paint mask''' is the most important.
| + | |
| | | | |
| − | Before entering the area that you are refinishing your project in take a air nozzle and blow yourself off. This will get rid of any extra surprises that will fall into your job
| + | ==Temperature== |
| | + | Warm and dry conditions are ideal for spray painting. The ambient temperature range for spraying most modern paints is about 65-90 degrees Fahrenheit. Be sure to choose the hardeners and reducers for the temperature range you'll be working in. Aerosols don't always work best in the damp and colder temperatures, which can hinder drying time, although it can be done. If it's not warm and dry outside, work in a well-ventilated garage, but set it up for painting. |
| | | | |
| − | == Spray gun Tech ==
| + | Try to keep your gun straight, not angled to far up or too far down. Keep the gun about 5 to 6 inches from the surface the whole time, or you will have heavy painted surfaces and lightly painted surfaces. Practice spray technique on an old fender to determine proper gun adjustment, pass speed, and pass overlap. |
| − | With any spray gun, you get what you pay for!
| + | |
| | | | |
| − | HVLP (High Volume Low Pressure) is the way to go when buying a spray gun although LVLP (Low Volume, Low Pressure) can work acceptably with the right paint. The prices have come down to reasonable levels, and the wasted paint by over spray (Not to mention the mess) makes a siphon-feed unit a poor choice for the home hobby sprayer.
| + | ==Building a temporary paint booth== |
| − |
| + | See: [[Building a paint booth]]. |
| − | Remember that high-solid primers like high-build type 2k urethanes require a larger (1.7mm) tip and setup internally than a regular paint gun. 3-gun sets are available for as little as $100 that include a primer gun with the larger tip, a paint/clear gun, and a 1.0mm tipped touch-up gun. Cutting (wet sanding) and buffing make up for a lot of shortcomings in inexpensive HVLP guns. So determining which is more valuable, your money or your time, is a determining factor in choosing a paint gun. A cheaper gun will require more time spent cutting and buffing than a top-of-the-line gun that lays paint out more evenly, but at an added price of several hundred dollars. A budget gun can be had for under $30, whereas a SATA 3000 digital runs around $650. You decide which is more important. Most folks will spend a little more time cutting and buffing than spend the extra on the fancy gun. The difference can be spent on go-fast goodies!
| + | |
| | | | |
| − | == Choosing the right type of paint ==
| + | {{Warning}}Before painting, remove all sources of ignition, including turning off gas water heaters and any pilot lights. |
| − | See "How to mix and spray urethane enamels" for a basic primer on the types of paint.
| + | |
| | | | |
| − | Whatever it is, you can ask other car builders that have done their own paint work, or if you know a painter, ask them. Best of all is to consult with the paint salesperson when you go to buy paint. They are a wealth of information. Utilize them. That's what they are there for.
| + | Painting in a garage lessens the chance of bugs or dust ending up lodged in your paint while it is still in its curing stage. One way to turn your garage into a temporary paint booth is to buy large plastic drop cloths from you local hardware or home improvement store. They are a cheap and effective way to protect your tool boxes and "toys" from overspray. |
| | | | |
| | + | A good rule of thumb for blower sizing is to try to change the air TWICE every minute. Hence, if you have a 10'x10'x10' paint booth (1000 cubic feet) you want a 2000 cfm blower (2000 cubic feet per minute). Open up your garage door about 1/8 to 1/4 up. This will help with ventilation, since solvents sink to the floor. Place a fan near the opening, facing outside, to help even more with airflow. Opening any side doors and roof vents and placing additional fans will help ventilation. Box fans may work, but at a minimum you should ensure that these fans are the brushless type to reduce the amount of sparking the exhaust stream will be exposed to to lessen the chance of an ignition. Remember, the fewer sparks the paint vapor "sees" the less likely you are to cause an explosion. |
| | | | |
| − | ''TWO MAIN TYPES OF ALL AUTOMOTIVE PAINT COLORS''
| + | An even better solution to box fans would be to use squirrel cage blowers, commonly found in HVAC and exhaust vent systems. Try to get the type where the motor is outside of the squirrel cage to reduce heating the exhaust stream. Place the squirrel cage blower motor outside of your "paint booth" and run ducting into (or out of) your paint booth. |
| | | | |
| | + | Something that will help keep dust and bugs from coming into your garage is to buy a furnace filter the same size as the window (or build a frame for the filters to go over your door) that you have open. This will collect the dirt and bugs before they become part of your paint job. If there are strict rules in your area, something that will help is to place a filter before your fan so that it filters the air as it is leaving your shop. |
| | | | |
| − | '''''SOLID paint'''''
| + | ==Basic mixing techniques== |
| − | Solid colors are a little easier than metallic to paint. If you mess up and get a run in them, they can be fixed rather easily by color sanding and buffing.
| + | Paint and related finishing products can be mixed in glass measuring cups, medicine cups, soup cans, or shot glasses. However, [http://www.ezmix.com/ E-Z Mix cups] are generally preferred for ease of use. Containers with measurements marked on the side are generally most useful. Paper cups are cautioned against because some may have a wax coating. Similarly, plastic cups or containers (medicine cups, yogurt containers, cleaned bottle caps, etc.) are also cautioned against. There are many different kinds of plastic, some of which are inappropriate for storing certain types of finishing products. |
| | | | |
| − | '''''Metallic paint'''''
| + | When mixing double portions of paint or primer, mix one portion at a time. For example, 8:2:1 easier to keep track of than 16:4:2. Most, if not all, automotive paint has the correct ratio for the paint/thinner/hardener printed on the label. If not, consult your favorite painter or paint store counter person for the correct ratio to use on your paint. |
| − | Spraying metallic is a little different then spraying a solid color, they will mottle (have blotches of dark and light areas) and tiger stripe if sprayed incorrectly. The key to spraying metallic paint is to move the "dry spot" around. For example, spray one coat one direction, then the next coat in the direction 90 degrees to the first coat. Overlapping the coats up to 75% is another key to good metallic finishes. Remember anytime that the paint moves the metallic does as well, so if they run you will get the metallic all in one spot. With metallic always use the suggested reducers and mix the entire batch to be sprayed at the same time. I recommend this ANYTIME you paint. DO NOT play mad scientist/chemist. FOLLOW the instructions to the letter. The engineers at the paint companies spend millions on R&D, so they are already sure of the results you will get by mixing the product any given way. You, however, as an amateur, are not. Do not re-invent the wheel.
| + | |
| | | | |
| − | ==Brian Martin's "Moving the Dry Spot" technique==
| + | After mixing each individual portion, add the two portions together and mix well again. This also cuts down on wasted material if you make a mistake (too much hardener, wrong reducer, etc.). |
| | | | |
| − | To prevent having a drier area at each of the seams, it is advised to "move the dry spot around". This technique is especially useful for fast-drying finishes, or for paint jobs with many coats of color. However, it can also be used for primers, sealers, colors and clears, urethanes, epoxies, and enamels. For more information, see Brian Martin's article in this Hotrodders Bulletin Board forum discussion: [http://hotrodders.com/forum/tip-day-30-a-74674.html Tip of the Day #30].
| + | ==Proper paint clothing== |
| | + | ===Suits=== |
| | + | When painting, it is always a good idea to wear some kind of protective clothing. It not only helps keep you from contacting the toxic materials but it also will help keep unwanted materials from getting on your paint job. The first and most important is a respirator made for '''automotive''' refinishing. There are a lot of companies that sell these. Get a paint suit or use a lint free pair of coveralls. Tyvek suits are available at many hardware stores for around $10. |
| | | | |
| − | == How to mix and spray Lacquer == | + | ===Gloves=== |
| | + | The next thing is a pair of gloves. Nitrile gloves hold up well to chemicals (see: [[Hand cleaner]]). Additionally, nitrile gloves will block the toxic isocyanates found in the activators of many 2k paints; latex will not block these chemicals. Do not use a set of rubber gloves as they are too clumsy and you need the motion that you get from the latex style gloves. |
| | | | |
| − | Lacquer has been used for many years in the hobby, and is used in a few restorations where the correct paint type will award/deduct points from a car. HOWEVER, due to V.O.C. requirements, the use of lacquer paints are becoming less and less welcome in most areas, and is actually illegal in most metropolitan areas. It is old technology, and is pretty much a dinosaur of the paint world.
| + | ===Head cover=== |
| | + | Get some kind of lint free head cover, this keeps your hair on your head and not on the job you are working on. You can also use a foot cover, which looks like a sock for your shoes. |
| | | | |
| − | There were and still are many good looking lacquer paint jobs out there. One of the pros is that it dries extremely hard with a quick drying time. THIS IS A FALSE MYTH. Lacquer never fully dries. If you spill gasoline on it, or many under-the-hood chemicals as used in the hobby, you will ruin your lacquer paint. Urethane enamel has replaced lacquer for a very good reason. It is much more durable. AND is more environmentally friendly than lacquer. Waterborne is the next wave of technology to lower painting emissions even further.
| + | ===Paint mask=== |
| − | You WILL NEED to sand and buff the whole project to get a smooth, shiny finish. If somebody is helping you spray it, they can know that modern lacquers will basically spray the same as the old lacquers. If you spray lacquer clear; the clear coat, (as long as it is a quality product) will be easier to control. | + | The most important item that you need is a paint mask. You can get by with out the other items (with extra buffing when you are done) but the paint mask is the most important. |
| − | You will need at least the same amount of thinner as you do paint to do a lacquer paint job.
| + | |
| | | | |
| − | == How to mix and spray Acrylic Enamel ==
| + | Before entering the area that you are refinishing your project in take a air nozzle and blow yourself off. This will get rid of any extra surprises that will fall into your job |
| − | When spraying acrylic enamel or any paint for that matter '''always read the can'''. Acrylic enamel is a strong paint that is used a lot in the fleet industry.
| + | |
| | | | |
| − | The start of any good paint job not including bodywork is a good sealer. They now have sealers that are color tint able in a urethane, which will take enamel topcoats if the directions are followed. The color tint able sealers help in coverage and if you do get one of those horrible rock chips they do not show nearly as bad. When starting the sealing processes it is always a good idea to use an epoxy or acid etch primer. The acid etch primer will hold out to rust a lot better then an epoxy does (i.e. I used it on the bare metal of my 70 nova did not spray the car for almost six months with only the acid etch on the car and I did not even get any facial rust, that came through, I have not had that good of an experience with epoxy sprayed it on my Buick and facial rust came through in a month).
| + | ==Health and Safety== |
| | + | Painting materials can do major harm to your health if you do not closely follow the manufacturers recommendations for skin and lung protection. |
| | | | |
| | + | Auto paints can contain many dangerous chemicals. It is important to protect yourself properly. |
| | | | |
| − | The best thing that you can do is to '''read the back of the can''' this will tell you the times that are needed in-between coats, dry times and the maximum amount of time between coats. If these are not followed you will get solvent popping and in the long run the potential for pealing paint. If you would like even more durability they also have clear coats for enamels. For the cost enamels are a good paint but the urethanes are a better product, they are starting to get affordable urethane paints now so do not rule them out.
| + | A respirator or fresh air system should be worn at all times when you are working with paints. Even when mixing your paint and getting ready. |
| | | | |
| − | == How to mix and spray Urethane Enamel ==
| + | More at [[Health and safety in the shop or garage]]. |
| | | | |
| − | FIRST OFF: URETHANE ENAMELS, WHEN MIXED, ARE VERY TOXIC TO HUMANS. You MUST wear a VOC compliant respirator at minimum when using these type of paints. A fresh air system is recommended, as is a painter's suit. These paints omit Volatile Organic Compounds, which are deadly the the human liver. DO NOT try to paint at home without an approved respirator, at the minimum. Ask your paint salesperson which one to buy. 3M makes a good one for under $20.
| + | ==Spray gun tech== |
| | + | With a spray gun, you get what you pay for! |
| | | | |
| − | Urethane enamel comes in two forms: Single stage, and Base coat/Clear coat. Single stage is the easiest to use, simply mix the two parts together, (The paint and the hardener) then reduce to spray and go at it. The single stage paint, like the base/clear, dries chemically by cross-linking together at a molecular level. Old lacquer paints and the Dupli-Color stuff at the local auto parts store dry by evaporation of solvent leaving the paint behind. Urethanes are MUCH stronger, as the name implies, they leave a urethane (plastic) coating on the car. Much better then old technology like lacquer.
| + | HVLP (High Volume Low Pressure) is the way to go when buying a spray gun although LVLP (Low Volume Low Pressure) can work acceptably with the right paint. The prices have come down to reasonable levels, and the wasted paint by overspray (not to mention the mess) makes a siphon-feed unit a poor choice for the home hobby sprayer. |
| | + | |
| | + | Remember that high-solid primers like high-build type 2K urethanes require a larger (1.7mm) tip and setup internally than a regular paint gun. Three gun sets are available for as little as $100 that include a primer gun with the larger tip, a paint/clear gun, and a 1.0mm tipped touch-up gun. Cutting (wet sanding) and buffing make up for a lot of shortcomings in inexpensive HVLP guns. So determining which is more valuable, your money or your time, is a determining factor in choosing a paint gun. A cheaper gun will require more time spent cutting and buffing than a top-of-the-line gun that lays paint out more evenly, but at an added price of several hundred dollars. A budget gun can be had for under $30, whereas a SATA 3000 digital runs around $650. You decide which is more important. A decent middle of the road option is a Finex 1000, 2000, 3000 series by Sharpe. The 1000 model is a small touch up gun, the 2000 a panel sized gun and the 3000 big enough for a complete vehicle. As of the year 2020, they run between $150-250 depending on size and where you buy. They have a pretty wide selection of tips/cones for spraying various viscosity coatings. Of course there are other brand name of spray guns and most have an economy line. One important tip! Any activated primer or paint WILL solidify in your gun if you don't clean it out within a certain amount of time. |
| | | | |
| − | Base/Clear, the other type of urethane, works a little differently. You first spray the color on the car, (The base coat) then apply a few coats of clear urethane over the base coat. The base clear has advantages over single stage, so let's compare the two.
| + | ==Choosing the right type of paint== |
| | + | If unsure, you can ask other car builders that have done their own paint work, or if you know a painter, ask them. Best of all is to consult with the paint salesperson when you go to buy paint. They are a wealth of information. Utilize them. That's what they are there for. |
| | | | |
| − | Advantages of single stage urethane:<br>
| + | ===Single stage:=== |
| | + | One stage, no clear coat. For people looking for a budget paint job. Not as glossy or durable as a 2 stage, although it easily oxidize or fade, it can easily be buffed out. |
| | | | |
| − | 1. Ease of use. Mix and spray, then walk away. You are done. Dries to the touch in a few hours.<br>
| + | *Synthetic enamel: dries naturally and leaves a glossy finish. Two parts- paint and reducer. |
| − | 2. Durable<br>
| + | |
| − | 3. Inexpensive. Single stage can be bought for around $50/gallon, enough ready to spray paint for an average car.<br>
| + | |
| − | 4. Can be had in most any color.<br>
| + | |
| | | | |
| − | Disadvantages:<br>
| + | *Acrylic enamel: just like synthetic, but with a hardener or catalyst. Cures within hours and a little more durable than synthetic enamel. |
| | | | |
| − | 1. Harder to repair a section if you mess up, (runs, etc.) and/or ding/scratch the car later. Cannot be blended as easily.<br>
| + | *Acrylic urethane: the most durable single stage paint. It has more UV and chip resistant over the enamel paint. |
| − | 2. Cannot be color sanded and buffed if metallic paint is used. What you spray is what you get.<br>
| + | |
| − | 3. Bugs, dirt, etc., are harder to get out of finished product unless a solid color is used.<br>
| + | |
| | | | |
| − | Now let's look at Base/Clear....<br>
| + | ===Two stage:=== |
| | + | *Base coat/clear coat :modern paint,the most durable of all. Gives the best gloss and longevity. But once the clear coat is gone you will need new paint job. |
| | | | |
| − | Advantages:<br>
| + | ===Three stage:=== |
| | + | Base coat, then pearl, candy or metallic, then a clear coat. (A candy coat has quite a bit of clear mixed in so that when you spray it, you don't completely cover the base color but instead, tint it) |
| | | | |
| − | 1. VERY hard to run the base coat, it sprays like lacquer. Easy to blend.<br>
| + | ==Two main types of all automotive paint colors== |
| − | 2. After clearing, can be wet sanded and buffed to a mirror finish. Easy to remove bugs, dust, etc.<br>
| + | |
| − | 3. Only slightly more expensive than single stage when budget brands are used. <br>
| + | |
| − | 4. Easier to use when multiple colors are used on the same car. I.E. stripes, etc.<br>
| + | |
| | | | |
| − | Disadvantages:<br>
| + | ===Solid paint=== |
| − | | + | Solid colors are a little easier than metallic to paint. If you mess up and get a run in them, they can be fixed rather easily by color sanding and buffing. |
| − | 1. Extra step involved. You spray the base coat, then have to spray the clear over it.<br>
| + | |
| − | 2. Extra materials to mix. <br>
| + | |
| − | 3. Slightly more expensive than budget single stage.<br>
| + | |
| − | | + | |
| − | | + | |
| − | Mixing and spraying:<br>
| + | |
| − | | + | |
| − | Mixing urethane enamel is really simple if you can follow basic instructions. They are right on the can, and most big manufactures' have the tech sheets on their websites to show everything you need to know about mixing it.
| + | |
| − | The person at the paint store when you buy your paint will prove to be invaluable when you talk to them and ask questions.
| + | |
| − | | + | |
| − | The basic recipe for urethanes (single stage)is this:<br>
| + | |
| − | Mix one gallon of color<br>
| + | |
| − | One quart of hardener<br>
| + | |
| − | One quart of reducer<br>
| + | |
| − | Go spray it.<br>
| + | |
| − | This varies from brand to brand slightly.
| + | |
| − | | + | |
| − | All you do then is spray away. REMEMBER, once mixed, the paint starts to cure and will be set up in an hour or so. If it sets up in your paint gun, you have a more-than-likely dead paint gun. Toss it in the garbage.
| + | |
| − | | + | |
| − | Base/clears work in a similar, by slightly different way. You mix<br>
| + | |
| − | The gallon of paint base<br>
| + | |
| − | A half gallon reducer<br>
| + | |
| − | and sometimes a few ounces of an activator<br>
| + | |
| − | then spray it out.
| + | |
| − | | + | |
| − | The clear mostly simply is one gallon of clear to
| + | |
| − | one quart of activator.
| + | |
| − | | + | |
| − | Spray it out.
| + | |
| − | | + | |
| − | Base clear can be cut after a couple days depending on the clear used. Then you have a finish that is UV ray
| + | |
| − | resistant, (READ: doesn't fade in the sun) and easy to care for.
| + | |
| − | | + | |
| − | Spraying: These paints are applied in a two or three coat method, depending on the product. Base coats, for example, are applied in a couple coats or until everything is covered. Clear is applied in three or even four heavier coats to allow for wet sanding and buffing. Single stage is applied in 3 coats normally.
| + | |
| − | | + | |
| − | HVLP (High Volume Low Pressure) paint guns have become so inexpensive that is is silly to try to paint without one, due to the amount of paint wasted by overspray using an old style siphon-feed gun.
| + | |
| − | | + | |
| − | == How to mix and spray Water based paints ==
| + | |
| | | | |
| − | == Paint Defects and Flaws == | + | ===Metallic paint=== |
| | + | Spraying metallic is a little different then spraying a solid color; they can easily mottle (have blotches of dark and light areas) and/or "tiger stripe" if sprayed incorrectly. The key to spraying metallic paint is to [http://www.hotrodders.com/forum/tip-day-30-a-74674.html move the "dry spot" around]. For example, spray one coat one direction, then the next coat in the direction 90 degrees to the first coat. Overlapping the coats up to 75% is another key to good metallic finishes. Yet another way is to do two wet coats, followed by a mist coat at just the right time. The mist coat will melt slowly into the wet coats yet leave an even metallic pattern. Most of this applies to a single stage metallic paint job. The base coat/clear coat systems are much more forgiving with metallics. |
| | | | |
| − | '''Orange Peel''' The most common paint defect, is caused by the paint being broken into small particles by the spray gun. It lands on the vehicle with little spaces in between droplets, leaving the texture, similar to the surface of an orange, behind. This is where the term "Orange peel" comes from. It is easily fixed by sanding the surface flat with 1200 grit sandpaper then polishing with a high-speed buffer and compounds.
| + | Remember, anytime that the paint moves the metallic does as well, so if they run you will get the metallic all in one spot. With metallic, always use the suggested reducers and mix the entire batch to be sprayed at the same time. DO NOT play mad scientist/chemist. ''Follow the instructions to the letter''. The engineers at the paint companies spend millions on R&D, so they are already sure of the results you will get by mixing the product any given way. Do not re-invent the wheel. |
| | | | |
| | + | ==Tips== |
| | + | *Always follow the manufacturers' recommendations for every product that you use. This usually means thoroughly reading the associated tech sheets, which are typically available for download from the manufacturer's website. For further detail, see [http://www.hotrodders.com/forum/rules-rules-rules-editorial-165210.html ''Rules, Rules, Rules'', an editorial post by MARTINSR on the Hotrodders Bulletin Board]. |
| | + | *Never soda blast unless you know how to completely remove the residue, and fully understand the complexities associated with soda blasting. See: [[Soda blasting]]. |
| | + | *A common problem with a first time painter is Orange Peel. To remove orange peel or minor cosmetic blemishes it is first recommended that you have your paint covered with a clear coat not only to protect it, but to enable you to have a mirror like finish. Wet-Sanding with 1500, and then 2000 grit to keep a very smooth finish. With a buffer and compound you can go as high as 4000 grit because of the way the liquid compound and buffer work. |
| | + | *After you Buff, you have the option of getting a swirl remover (liquid) and waffle foam pad. These 2 items together will help you get rid of the buff swirls, and leave your paint in brand new condition as if it just came off of the showroom floor. |
| | | | |
| − | '''Fish Eyes''' Fish eyes are a separation of the paint normally resembling the look of a fish eye. These are areas where the paint will not adhere thus making small craters in the paint. Fish eyes are always caused by contamination. The oil naturally present in your fingers is probably the number one cause of fish eyes. You will see most all good painters and body men wearing latex gloves similar to what doctors wear when prepping a car for paint. Wax, silicones, diesel fuel, and products such as Armor All can all cause the problem. The contamination is usually on the surface being painted but can also result from contaminated paint and contaminated air. Using a wax and grease remover, proper air filters and general cleanliness around the paint area should stop the occurrence of fish eyes.
| + | ===Forums=== |
| | + | *[http://autobody101.com/forums/ Autobody101.com forums] |
| | + | *[http://www.autobodyonline.com/discussion/ Autobodyonline.com forums] |
| | + | *[http://autobodystore.com/forum/index.php Autobodystore forums] |
| | + | *[http://www.hotrodders.com/forum/body-exterior Hotrodders.com body and exterior forum] |
| | + | *[http://spi.forumup.org SPI Users forum] |
| | | | |
| | + | ===Videos=== |
| | + | *[http://commerce03.i2net.com/able55new/stores/10/Huntington-Beach-Bodyworks-56-Metal-to-Paint-P14876C596.aspx Huntington Beach Bodyworks 56' Metal to Paint] |
| | | | |
| − | '''Solvent Pop''' Solvent pop is tiny pinpoint size craters in the paint surface. This defect is produced when the top surface of the paint dries before the lower portion resulting in trapped solvents. The trapped solvents escape explosively through the dry skin of the paint leaving tiny craters. Solvent pop most often occurs because the job is being rushed either with flash times or the speed of the products. Most times they can be prevented by slowing down the painting process. Adequate flash time is essential to prevention as solvents need time to escape. Slower reducers and activators can also be used to prevent solvent pop as this too allows more time for the solvents to escape. Solvent pop can also be caused by excessive air movement which causes the top surface of the paint to skin over too fast.
| + | ==References== |
| | + | *http://www.hotrodders.com/forum/metal-prep-epoxy-primer-no-so-fast-164937.html |
| | + | *http://spi.forumup.org/about2379-0-asc-0-spi.html (lots of tips here, needs to be incorporated into article) |
| | | | |
| − | == How to finish off your paint job (Buffing) == | + | ==Resources== |
| | + | *[[Building a paint booth]] |
| | + | *[[Cheapo paint job]] |
| | + | *[[Body and exterior tips]] |
| | + | *[[Health and safety in the shop or garage]] |
| | | | |
| − | Buffing is a whole other technique that you do when painting your car, it will be discussed in detail in its own article: [[Buffing your newly-finished paint]]
| |
| | | | |
| | [[Category:Body and exterior]] | | [[Category:Body and exterior]] |
| − | {{youcanedit}}
| |
Your Privacy Choices