Bulletproof cooling system
From Crankshaft Coalition Wiki
| Line 1: | Line 1: | ||
| − | |||
| − | |||
[[File:Engine-cooling-system.jpg|thumb|600px|right|Typical cooling system, some engines use an internal bypass]] | [[File:Engine-cooling-system.jpg|thumb|600px|right|Typical cooling system, some engines use an internal bypass]] | ||
| Line 123: | Line 121: | ||
Most cars from 1960 and up used cross flow radiators. One of the reasons was a lower hoodline, and two, more cooling area was required to cool the larger engines. Cross flow radiators had a tank with an inlet/outlet placed on either side. The water entered on one side and passed through the core of the rad, was cooled by the air flow and the heat escaped through convection to the outside air. Engineers found that the longer the liquid was exposed to the cooling flow of air through the radiator core, the more heat could be extracted from the flowing water. They slowed down the water travel by increasing the size of the water pump pulleys, but that had its limitations. They also added more rows of core, but that too had limitations. | Most cars from 1960 and up used cross flow radiators. One of the reasons was a lower hoodline, and two, more cooling area was required to cool the larger engines. Cross flow radiators had a tank with an inlet/outlet placed on either side. The water entered on one side and passed through the core of the rad, was cooled by the air flow and the heat escaped through convection to the outside air. Engineers found that the longer the liquid was exposed to the cooling flow of air through the radiator core, the more heat could be extracted from the flowing water. They slowed down the water travel by increasing the size of the water pump pulleys, but that had its limitations. They also added more rows of core, but that too had limitations. | ||
| − | Road course racers found a way to keep cooling to a simple easy form. To do this, they pulled the tanks off the radiators that they were using and placed baffle plates in the tank covers. The baffles were placed so as to divide the radiator core section into three distinct areas. Water would enter the upper radiator inlet on the right side and would flow across the top section of the radiator to the left side, a baffle plate located 2/3 of the way down the tank caused the coolant to flow across the radiator to the right side to the right radiator tank. The coolant couldn't rise upwards because a baffle plate located 1/3 of the way down stopped it and forced it to head down lower in the right tank, where it again was drawn across the radiator core to the lower left tank outlet and out to the engine. This serpentine course that the coolant took allowed the coolant to be cooled THREE TIMES by the cooling air flow coming through the core area. "Excellent idea!" you say, “Why don't they do that to all cars today? | + | Road course racers found a way to keep cooling to a simple easy form. To do this, they pulled the tanks off the radiators that they were using and placed baffle plates in the tank covers. The baffles were placed so as to divide the radiator core section into three distinct areas. Water would enter the upper radiator inlet on the right side and would flow across the top section of the radiator to the left side, a baffle plate located 2/3 of the way down the tank caused the coolant to flow across the radiator to the right side to the right radiator tank. The coolant couldn't rise upwards because a baffle plate located 1/3 of the way down stopped it and forced it to head down lower in the right tank, where it again was drawn across the radiator core to the lower left tank outlet and out to the engine. This serpentine course that the coolant took allowed the coolant to be cooled THREE TIMES by the cooling air flow coming through the core area. "Excellent idea!" you say, “Why don't they do that to all cars today? Because if the water actually got to ambient, in this situation, then some part of this radiator would not be doing any cooling at all. So there is a trade off, as well as the slowing of coolant through the block in this set up. If it stays in the block too long, steam pockets, and bubbles will begin to overheat, so in theory, if double pass and triple pass worked in all situations, then factories would be making them in productions. |
| − | <br style="clear:both"/> | + | |
| + | <br style="clear:both"/> | ||
==Does radiator tube size matter?== | ==Does radiator tube size matter?== | ||
| + | |||
| + | <BR> | ||
| + | |||
The automotive radiator is essentially just another name for a heat exchanger, whereby combustion temperatures are transferred to the cooling system of the engine block and taken outside the block via flexible radiator hoses to be exposed to the cooling force of air through the radiator core, thus reducing the temperature of the coolant before returning it to the engine block. There are two restrictions in the system. One is the thermostat, which restricts flow and holds heat in the engine until warmed up, and the other is the radiator core tubes. The radiator tubes have to be of sufficient size so as to allow the coolant to flow through in an unrestricted manner, but also able to 'scrub off' BTU's or heat; which is based on the shape of the tube and the convection of heat away from the coolant to the outside air. A wide flat tube will expose more surface area to the outside flow of air than a narrow tube. The reason for this is more surface area is exposed to cooling. Look at the pictures located below and see why that is. | The automotive radiator is essentially just another name for a heat exchanger, whereby combustion temperatures are transferred to the cooling system of the engine block and taken outside the block via flexible radiator hoses to be exposed to the cooling force of air through the radiator core, thus reducing the temperature of the coolant before returning it to the engine block. There are two restrictions in the system. One is the thermostat, which restricts flow and holds heat in the engine until warmed up, and the other is the radiator core tubes. The radiator tubes have to be of sufficient size so as to allow the coolant to flow through in an unrestricted manner, but also able to 'scrub off' BTU's or heat; which is based on the shape of the tube and the convection of heat away from the coolant to the outside air. A wide flat tube will expose more surface area to the outside flow of air than a narrow tube. The reason for this is more surface area is exposed to cooling. Look at the pictures located below and see why that is. | ||
Your Privacy Choices