Automobile body and frame rotisserie
From Crankshaft Coalition Wiki
(→Reference: Format) |
(→References) |
||
| Line 1: | Line 1: | ||
| − | + | ||
| − | [[Image: Rotisserie.jpg|right|frame|none|FrameOff© BodyMaster™ | + | [[Image: Rotisserie.jpg|right|frame|none|FrameOff© BodyMaster™ system]] |
<br><br><br><br><br><br><br> | <br><br><br><br><br><br><br> | ||
| − | == Purpose == | + | == Purpose of a rotisserie == |
| − | # | + | # To remove the accumulation of dirt, rust, grease, etc. from vehicles chosen for restoration or rodding. Not suited for ordinary servicing and repair. Ramps and lifts are better suited for this. |
| − | # | + | # Gives access to all areas for cleaning and repair. |
| − | # | + | # Eliminates hours of looking up into nooks and crannies or laying beneath the underside of a vehicle while scraping, brushing, sanding, and doing repairs. |
== Design parameters and considerations== | == Design parameters and considerations== | ||
# Load -- consider weight and flex of body. If the load gets outside of the base, the whole thing tips over. | # Load -- consider weight and flex of body. If the load gets outside of the base, the whole thing tips over. | ||
# Swing -- consider shape and dimensions of body and the space in which it will rotate about its center of gravity. Pivots must be in line. Anything on a radius from either pivot will reduce the swing capacity; distance of pivot from obstructions determines swing capacity. | # Swing -- consider shape and dimensions of body and the space in which it will rotate about its center of gravity. Pivots must be in line. Anything on a radius from either pivot will reduce the swing capacity; distance of pivot from obstructions determines swing capacity. | ||
| − | |||
| − | |||
# If the vehicle is not braced properly especially a convertible you can easily bend or twist the body. | # If the vehicle is not braced properly especially a convertible you can easily bend or twist the body. | ||
| − | == | + | |
| − | # Acquisition of materials -- salvage, new | + | == Building a rotisserie == |
| − | # | + | # Materials -- steel pipe, tubing, angle, plate, bolts, welding rods or wire |
| − | # Work area | + | ## Acquisition of materials -- salvage, new |
| − | + | # Construction methods -- weld, bolt | |
| + | # Tools needed | ||
| + | ##welder | ||
| + | ##torch | ||
| + | ##drill | ||
| + | ##saw | ||
| + | ##layout tools (scribe, awl, soapstone, marker, square, level, straight edge) | ||
| + | ##wrenches | ||
| + | # Work area | ||
== Usage == | == Usage == | ||
| − | # Safe attachment of load | + | # Safe attachment of load |
| − | # Safe elevation of load | + | # Safe elevation of load |
| − | # Test and inspect | + | # Test and inspect |
| − | == | + | ==Other uses for rotisserie== |
| − | + | # Storage | |
| − | # Storage | + | #I built my very simple rotisserie and after taking my '68 Firebird off of it 2 years later, I cut the tops off, added casters, welded them together, and VOILA!...instant rollaround car stands. Of course, the rotisserie only made the rear part, I made the front part from some spare steel I had. Here's a photo of it... |
| − | + | ||
| − | + | ||
| − | I built my very simple rotisserie and after taking my 68 Firebird off of it 2 years later, I cut the tops off, added casters, welded them together, and VOILA!...instant rollaround car stands. Of course, the rotisserie only made the rear part, I made the front part from some spare steel I had. Here's a photo of it... | + | |
[[Image:100_2798.jpg]] | [[Image:100_2798.jpg]] | ||
| Line 37: | Line 40: | ||
[[Image:rotiss2.jpg]] | [[Image:rotiss2.jpg]] | ||
| − | <p>This is my first rotisserie I | + | <p>This is my first rotisserie. I built over 10 years ago. I designed it with pneumatic tires and steering to allow for mobility on rough outdoor surfaces and ease of trailer loading (back then I moved my vehicles around between home and work fabrication shops). This particular rotisserie was sized so that when the body is flipped roof up, I can practically work underneath the car while standing straight (notice a wide track to enhance stability). The rotisserie can be disconnected in the middle for painting large parts.-Rich TFS</p> |
| + | |||
| + | ==References== | ||
| − | |||
| − | |||
| − | |||
;Discussion on Hotrodders.com | ;Discussion on Hotrodders.com | ||
*[http://www.hotrodders.com/forum/tilter-rotisserie-ramp-79099-2.html Tilters, rotisseries] | *[http://www.hotrodders.com/forum/tilter-rotisserie-ramp-79099-2.html Tilters, rotisseries] | ||
| Line 47: | Line 49: | ||
==External links== | ==External links== | ||
| − | + | ||
| − | + | ||
*[http://www.mckennasgarage.com/xke/jag6.htm Building a rotisserie] | *[http://www.mckennasgarage.com/xke/jag6.htm Building a rotisserie] | ||
*[http://www.harwoodperformance.bizland.com/1941buick/Editorial_20.htm Rotisserie construction] | *[http://www.harwoodperformance.bizland.com/1941buick/Editorial_20.htm Rotisserie construction] | ||
| − | + | <br> | |
[[Category:Garage and shop]] | [[Category:Garage and shop]] | ||
| − | |||
Your Privacy Choices