How to rebuild automotive carburetors
From Crankshaft Coalition Wiki
m (Add links) |
|||
| Line 1: | Line 1: | ||
| − | + | ||
==Introduction== | ==Introduction== | ||
Sooner or later, every hotrodder runs into the steps of making induction and carburetion choices while building a performance engine. | Sooner or later, every hotrodder runs into the steps of making induction and carburetion choices while building a performance engine. | ||
| Line 22: | Line 22: | ||
Often the best place to start is to baseline the carb back to factory specs. This eliminates any chance that a previous owner's changes will mess up the way the carb works on your engine. | Often the best place to start is to baseline the carb back to factory specs. This eliminates any chance that a previous owner's changes will mess up the way the carb works on your engine. | ||
| − | [[Media:HolleyCarbList.pdf|'''Aftermarket Holley carb numerical listing''']] by carb number shows the factory specs as well as the part numbers for rebuild kits and gaskets. To compare metering plates to jet sizes, see the info [[Media:08 Holley Catalog pages - 90.pdf|'''here''']]. | + | *[[Media:HolleyCarbList.pdf|'''Aftermarket Holley carb numerical listing''']] by carb number shows the factory specs as well as the part numbers for rebuild kits and gaskets. |
| + | *'''[[Holley HP series carb specs]]''' by carb number | ||
| + | *To compare metering plates to jet sizes, see the info [[Media:08 Holley Catalog pages - 90.pdf|'''here''']]. | ||
<br style="clear:both"/> | <br style="clear:both"/> | ||
| Line 61: | Line 63: | ||
<br style="clear:both"/> | <br style="clear:both"/> | ||
| − | [[File:Oring holley sec.jpg|thumb|350px|Arrow indicates cork O-ring that seals the vacuum chamber to the main carb body]] | + | [[File:Oring holley sec.jpg|thumb|left|350px|Arrow indicates cork O-ring that seals the vacuum chamber to the main carb body]] |
Use a fresh cork O-ring to seal the secondary vacuum chamber assembly to the carb body. Using a light smear of Hylomar on the cork gasket helps it to seal and stay pliable. A small rubber O-ring may be used instead of the cork gasket to seal a Holley secondary chamber. If you try this, be sure the O-ring is sealing, w/o being ''too'' thick. | Use a fresh cork O-ring to seal the secondary vacuum chamber assembly to the carb body. Using a light smear of Hylomar on the cork gasket helps it to seal and stay pliable. A small rubber O-ring may be used instead of the cork gasket to seal a Holley secondary chamber. If you try this, be sure the O-ring is sealing, w/o being ''too'' thick. | ||
<br style="clear:both"/> | <br style="clear:both"/> | ||
| − | Be sure the vacuum chamber is assembled correctly. The diaphragm can | + | [[File:Holley sec checkball.jpg|thumb|450px|Secondary vacuum chamber check ball]] |
| − | + | Be sure the vacuum chamber is assembled correctly. The diaphragm can be torn or perforated; if that happens there will be no or very slow to activate with incomplete opening of the secondaries. Also, the check ball can get left out or can stick, or the check ball seat can be rough, allowing the secondaries to activate too easily. So be sure the check ball is present and the seat is well formed. | |
| − | + | ||
| + | The seat can be re-formed by using an old check ball and a small punch. Drop the check ball into the check ball passage, then with the vacuum chamber solidly supported, lightly tap the old check ball with the punch and a small hammer. This re-forms the seat. | ||
| + | <br style="clear:both"/> | ||
'''NOTE:''' There are small grooves in the vacuum chamber check ball seat. This is normal, so do not try to use this method to remove the grooves. They need to be there to allow the secondaries to work correctly. | '''NOTE:''' There are small grooves in the vacuum chamber check ball seat. This is normal, so do not try to use this method to remove the grooves. They need to be there to allow the secondaries to work correctly. | ||
| Line 110: | Line 113: | ||
The difference between the correct and too rich/lean jet sizes may only be 0.002”-0.004”. There are no readily available drill bits that are that close in size to one another. So at best, the changes made to jets by hand drilling are going to be in steps decided by the availability of drill bits. Because drill bits are often available in 1/64” increments (the small numbered bits- which have a finer increment between bits- are too small for drilling the average carb metering jet), this will be on the order of a 0.0156” change between drill bits- which is HUGE (~40%) change in metering area when in the 0.070” jet orifice range. | The difference between the correct and too rich/lean jet sizes may only be 0.002”-0.004”. There are no readily available drill bits that are that close in size to one another. So at best, the changes made to jets by hand drilling are going to be in steps decided by the availability of drill bits. Because drill bits are often available in 1/64” increments (the small numbered bits- which have a finer increment between bits- are too small for drilling the average carb metering jet), this will be on the order of a 0.0156” change between drill bits- which is HUGE (~40%) change in metering area when in the 0.070” jet orifice range. | ||
| − | + | There is no practical way for a person to casually drill an orifice and know what the change in flow will be. Drilling orifices by hand is mostly an anachronism. Nowadays, better options are almost always readily available. Only rare and/or extreme circumstances dictates such practices. | |
| + | |||
| + | Highly educated engineers work with mathematical formulas to design correct sized orifices. During the formative years of our contemporary automotive racing environments, carburetors were not always made with a full range of ready made fuel and air bleed orifice replacements so carburetor tuning 'magic' was done with a drill. Because of the difficulty in obtaining precision, for those reasons listed above, a general recommendation to purchase an assortment of pre-calculated metering orifices (fuel or air bleeds) is emphasized. Nevertheless, carburetors exist that do not have readily available interchangeable orifices, and these warnings are made to caution the ambitious tuner. | ||
===Quadrajet Tuning and Repair Parts=== | ===Quadrajet Tuning and Repair Parts=== | ||
| Line 120: | Line 125: | ||
==Carter carb== | ==Carter carb== | ||
| − | [http://www.mymopar.com/downloads/carterafbtuning.pdf Carter AFB Selection and Tuning Guidelines] from Federal Mogul | + | ===AFB=== |
| + | *[http://www.mymopar.com/downloads/carterafbtuning.pdf Carter AFB Selection and Tuning Guidelines] from Federal Mogul | ||
| + | *[[Media:Afb rebuild guide.pdf|How to Overhaul and Tune your Carter AFB or Edelbrock EPS Four Barrel Carburetor]] | ||
| + | *[[Media:Carterafbtuning.pdf|Carter AFB Selection and Tuning Guidelines]] | ||
| + | ===Thremoquad=== | ||
[[Image:Thermoquad.jpg]] | [[Image:Thermoquad.jpg]] | ||
| Line 152: | Line 161: | ||
[[Category:Carburetors]] | [[Category:Carburetors]] | ||
[[Category:Engine]] | [[Category:Engine]] | ||
| − | |||
Your Privacy Choices