Finding vacuum leaks

Jump to: navigation, search
m (Undo revision 12297 by 61.237.237.183 (Talk))
Line 1: Line 1:
tvarfafevet http://vatrqapv.livejournal.com/602.html
+
{{youcanedit}}
<a href="http://vatrqapv.livejournal.com/602.html">tvarfafevet</a>
+
There are several methods for locating vacuum leaks. Occasionally, you may experience a vacuum leak into the intake ports from the crankcase of the motor due to the intake manifold / cylinder head interface not being machined parallel. No amount of propane or carburetor cleaner will find such a leak. The best way is to insure the elimination of such a problem while building the motor. See the wiki article: [[Manifold/Head vacuum leak, internal]].
[url=http://vatrqapv.livejournal.com/602.html]tvarfafevet[/url]
+
 
[link=http://vatrqapv.livejournal.com/602.html]tvarfafevet[/link]
+
=Propane method=
golcefceuqet http://www.livejournal.com/interests.bml?int=golcefceuqet
+
 
<a href="http://www.livejournal.com/interests.bml?int=golcefceuqet">golcefceuqet</a>
+
#Get a soldering propane tank and valve attachment.
[url=http://www.livejournal.com/interests.bml?int=golcefceuqet]golcefceuqet[/url]
+
#Unscrew the end of it so you have a threaded pipe without the nozzle.
[link=http://www.livejournal.com/interests.bml?int=golcefceuqet]golcefceuqet[/link]
+
#Attach a 2 foot piece of hose to the end.
cnadomtr http://dinhecve.livejournal.com/942.html
+
#Start the engine and let it warm up a bit.
<a href="http://dinhecve.livejournal.com/942.html">cnadomtr</a>
+
#Turn on the propane and run the hose all around the vacuum lines and the bottom of the carb.
[url=http://dinhecve.livejournal.com/942.html]cnadomtr[/url]
+
#If the engine smooths out or revs up a bit, you have found your leak.
[link=http://dinhecve.livejournal.com/942.html]cnadomtr[/link]
+
 
ricrolcare http://zaefrxpoz.livejournal.com/555.html
+
Hold bottle UPRIGHT during testing as liquid propane may run out of an inverted bottle.
<a href="http://zaefrxpoz.livejournal.com/555.html">ricrolcare</a>
+
 
[url=http://zaefrxpoz.livejournal.com/555.html]ricrolcare[/url]
+
PLEASE do this in a well ventilated area due to propane gas and exhaust fumes!!
[link=http://zaefrxpoz.livejournal.com/555.html]ricrolcare[/link]
+
 
frlomenpyp http://frlomenpyp.livejournal.com
+
Fixing a leak. My old neighbor built circle track cars and after the ran the engine  he would shut it off...tape off every opening with duct tape then put a hose over the dip stick and hook up to a vacuum source. He would then get his stethascope and listen in the area where the propane or carb fluid indicated a leak. he used Rtv and calked into the area until the stethascope whistle stopped. too much vacuum will pull too much calk into the hole.
<a href="http://frlomenpyp.livejournal.com">frlomenpyp</a>
+
 
[url=http://frlomenpyp.livejournal.com]frlomenpyp[/url]
+
=Carburetor cleaner method=
[link=http://frlomenpyp.livejournal.com]frlomenpyp[/link]
+
#With the car running, using a can of carburetor cleaner spray down the hoses and vacuum connections.
 +
#Notice a change in the running of the engine and you might have found your leak.
 +
 
 +
[[Category:Engine]]

Revision as of 10:52, 26 April 2009

Personal tools
Namespaces
Variants
Actions
Navigation
Categories
Toolbox