Fat-fendered Ford battery tray

Jump to: navigation, search
m (Preamble)
m (How to build it)
Line 10: Line 10:
  
 
==How to build it==
 
==How to build it==
Begin by taking a small cardboard box much the same size as that battery that you will be using. It is easier to handle than a regular 40-pound battery with clothing-eating acid spewing from it when dropped. Even using a box an inch or so larger will give you additional clearances for cables and hold-downs. Place the box against the frame area and try to imagine what kind of bracket you will have to build to get it to stay there. You can use duct tape to secure the box in place while you play with flexible steel strapping (usually found on packing crates) that you can shape into 90 degree bends to hold up the box (battery).  
+
Begin by taking a small cardboard box much the same size as the battery you'll be using. A cardboard mock-up is easier to handle than a regular 40-pound acid-filled battery. A box an inch or so larger will give you additional clearances for cables and hold-downs. Place the box against the frame area and try to imagine what kind of bracket required to hold it there. You can use duct tape to secure the box in place while you play with flexible steel strapping (usually found on packing crates) that you can shape into 90 degree bends to hold up the box (battery).  
  
The location should be a place where you can access the battery for servicing or removal, a place where mechanical damage from flying debris, i.e. stones, etc. is at a minimum or a accessory shield can be installed to protect the battery casing. The frame of the vehicle should be close to the location as it is one of the strongest mounting points that can be offered.
+
The location should be a place where you can access the battery for servicing or removal; a place where potential damage from flying debris, i.e. stones and such, is at a minimum. An accessory shield can be added to further protect the battery casing. Ideally, the frame of the vehicle should be close to this location as it is one of the strongest mounting points available.
  
What about water and dampness? Most batteries manufactured today are sealed maintainance-free units and are 99% sealed against outside water sources. Cable connections should be coated with dielectric grease to seal out corrosion. In addition, you can put your battery in a plastic marine battery case, which will provide both waterproofing and protection from mechanical damage.
+
"What about water and dampness?" you ask. Well, most modern batteries are sealed, maintainance-free units, 99 percent impervious to outside water sources. Cable connections should be coated with dielectric grease to seal out corrosion. In addition, you can put your battery in a plastic marine battery case, which will provide both waterproofing and protection from mechanical damage.
  
If you are using a plastic marine battery case, then use that instead of the cardboard box to find your location.
+
A plastic marine battery case can also be used instead of the cardboard box to find your location.
  
You can use cardboard to form a tray to hold the battery and by making a 90 degree bend in the cardboard, you can run it up along side of the frame and use the frame to stabilize and mount the tray to. You can use nuts and washers, brackets, etc to extend out from the frame to give the tray a solid mounting surface.
+
You can use cardboard to form a tray to hold the battery and, by making a 90 degree bend in the cardboard, you can run it up along side of the frame and use the frame to stabilize and mount the tray. You can use nuts, washers, brackets...etc to extend out from the frame, giving the tray a solid mounting surface.
  
To utilize the vertical side of the tray, a cutout can be made and bent outward using to 45 degree bends and adding a hole for a mounting bolt to make an offset for a mounting location to the frame. If laid out correctly, all three sides plus the bottom can be cut out of one piece of flat stock and bent to form the final battery tray. See pictures.
+
To utilize the vertical side of the tray, a cutout can be made and bent 45 degree outward, adding a hole for a mounting bolt to create an offset for a mounting location to the frame. If laid out correctly, all three sides plus the bottom can be cut out of one piece of flat stock and bent to form the final battery tray. See pictures.
  
 
==Construction==
 
==Construction==

Revision as of 22:33, 10 February 2010

Personal tools
Namespaces
Variants
Actions
Navigation
Categories
Toolbox