How to make a timing tape
m |
m |
||
| Line 1: | Line 1: | ||
| − | + | ==Overview== | |
| + | Making a semi-permanent timing tape is very easy. It replaces the need for a "dial back" timing light and removes any doubt as to where the timing marks are supposed to be. | ||
| − | + | ==Procedure== | |
| + | |||
| + | ===Find TDC=== | ||
| + | You need to know (or verify) that the TDC or "0" degree line on the damper or balancer (henceforth to be called a "damper") and the timing tab or mark actually correctly represents "0" degrees (TDC). | ||
| + | One method to find TDC is by using a piston stop and fabricate a timing "tab" (often a stiff piece of wire secured behind a convenient bolt head) that aligns with the line on the damper to represent "0" or TDC. Help with this can be found at [http://www.crankshaftcoalition.com/wiki/Determining_top_dead_center Determining top dead center]. | ||
| − | + | ===Once TDC has been established, the rest goes like this:=== | |
| − | + | *Using either a string, ruler or a seamstress' cloth tape measure, measure the circumference of the damper. If you only have a straight ruler, measure the diameter and multiply by 3.1416 (pi) to get the circumference. | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | Using either a string, ruler or a seamstress' cloth tape measure, measure the circumference of the damper. If you only have a straight ruler, measure the diameter and multiply by 3.1416 (pi) to get the circumference. | + | |
| − | Once the circumference is known, 1/10 (10%) of this figure represents 36º. Half of that is 18º, half again is 9º, etc. It doesn't matter what units are used to measure the circumference- metric, inch, or | + | *Once the circumference is known, 1/10 (10%) of this figure represents 36º. Half of that is 18º, half again is 9º, etc. It doesn't matter what units are used to measure the circumference- metric, inch, or nanoparsecs. |
| − | If you want to use the metric system, multiply the circumference by 25.4 to convert to millimeters. Divide this by 360 and you'll get the measurement in millimeters that equal one degree. | + | *If you want to use the metric system, multiply the circumference by 25.4 to convert to millimeters. Divide this by 360 and you'll get the measurement in millimeters that equal one degree. |
| − | Careful measurement and marking of the degrees in this fashion on a length of masking tape can then be applied to the damper, aligning TDC or "0" on the tape to the line on the balancer, with the degrees BTDC to the '''right''' of this mark. | + | *Careful measurement and marking of the degrees in this fashion on a length of masking tape can then be applied to the damper, aligning TDC or "0" on the tape to the line on the balancer, with the degrees BTDC to the '''right''' of this mark. |
| − | You can also measure the length between the timing tab marks and transfer them onto tape, i.e. if there's 3/4 of an inch (0.750") representing 10º on the tab, two marks 3/4 of an inch (0.750") apart on your tape will also be 10º. This will work- provided that the timing tab is correct for the application and not for a different diameter damper. | + | *You can also measure the length between the timing tab marks and transfer them onto tape, i.e. if there's 3/4 of an inch (0.750") representing 10º on the tab, two marks 3/4 of an inch (0.750") apart on your tape will also be 10º. This will work- provided that the timing tab is correct for the application and not for a different diameter damper. |
Your Privacy Choices