1937-1957 Buick Oldsmobile Pontiac suspension upgrade

Be sure the frame is level side to side and has the correct front to rear angle that you want.  (with 15 inch wheels, my spindle center was 12.5 inches off the ground. I blocked the frame, so that when the lower A was level, the spindle was 12.5 in up)  Even a small error here will be costly.  It takes ½ inch of shims to adjust 1 degree of camber. If you need to put additional shims on therear of the bracket, to increase caster, and can’t take enough out of the front to keep the camber static, you will have to cut it loose and start over.  Unfortunately, you can’t do a full alignment until it is totally finished, basically driveable. So get this part right. If you have any doubts, shade towards the positive camber side, you can add more shims later to move it towards negative.  Likewise, move the upper mount to a position about 3/4 inch behind the plumb line for the spindle, to set up at least 5 * of caster in the neutral position (neutral being the static position as mocked up, before final alignment).  If you intend to add power steering, I would shoot for 6 * in the neutral position, but don’t get the uppers so far behind the lowers you put the ball joints in a bind. I drilled holes in the bottom plate of the angle iron and when I had it mocked up, I drilled thru the frame and bolted it up with 3/8 inch bolts.  This was strong enough to allow me to assemble the entire front end, with springs, put the wheels and tires on it and set it on the ground.  Since I had my engine in, I was basically in a final drive setup. I double checked everything, then tore it down and had it welded in place.

Be sure the frame is level side to side and has the correct front to rear angle that you want.  (with 15 inch wheels, my spindle center was 12.5 inches off the ground. I blocked the frame, so that when the lower A was level, the spindle was 12.5 in up)  Even a small error here will be costly.  It takes ½ inch of shims to adjust 1 degree of camber. If you need to put additional shims on therear of the bracket, to increase caster, and can’t take enough out of the front to keep the camber static, you will have to cut it loose and start over.  Unfortunately, you can’t do a full alignment until it is totally finished, basically driveable. So get this part right. If you have any doubts, shade towards the positive camber side, you can add more shims later to move it towards negative.  Likewise, move the upper mount to a position about 3/4 inch behind the plumb line for the spindle, to set up at least 5 * of caster in the neutral position (neutral being the static position as mocked up, before final alignment).  If you intend to add power steering, I would shoot for 6 * in the neutral position, but don’t get the uppers so far behind the lowers you put the ball joints in a bind. I drilled holes in the bottom plate of the angle iron and when I had it mocked up, I drilled thru the frame and bolted it up with 3/8 inch bolts.  This was strong enough to allow me to assemble the entire front end, with springs, put the wheels and tires on it and set it on the ground.  Since I had my engine in, I was basically in a final drive setup. I double checked everything, then tore it down and had it welded in place.

For spindles, I started with the 63 Pontiac spindles as advised in the article.  ( Tapered bearings and a good Scarebird kit available.)  Unfortunately when I set it on the ground, it was too high.  This led to a search for dropped spindles.  BOP – they don’t exist.  

For spindles, I started with the 63 Pontiac spindles as advised in the article.  ( Tapered bearings and a good Scarebird kit available.)  Unfortunately when I set it on the ground, it was too high.  This led to a search for dropped spindles.  BOP – they don’t exist.  

Chevy drop spindles are readily available, but they come with a problem. Note the side by side comparisons in the picture.  The 63 Pontiac spindle has a deep 90* bend at the bottom.  That is to clear the wide corners on the lower control arm.  The 60’s stock Chevy spindle has a 45* angle there, and won’t work.   

Chevy drop spindles are readily available, but they come with a problem. Note the side by side comparisons in the picture.  The 63 Pontiac spindle has a deep 90* bend at the bottom.  That is to clear the wide corners on the lower control arm.  The 60’s stock Chevy spindle has a 45* angle there, and won’t work.   

The third spindle is the 65-70 Chevy drop spindle from CPP (Classic Performance Products). It is their own in house design and is very close to the dimensions/configuration of a Pontiac spindle.  I had to trim the ears off the front side of the lower A frame, but that was a minor modification.  

The third spindle is the 65-70 Chevy drop spindle from CPP (Classic Performance Products). It is their own in house design and is very close to the dimensions/configuration of a Pontiac spindle.  I had to trim the ears off the front side of the lower A frame, but that was a minor modification.