How to identify a Ford V8
Crashfarmer (Talk | contribs) (→Flathead Ford V8 (136/221/239/255/337)) |
Crashfarmer (Talk | contribs) (→335 Series Engine Family (Cleveland) (302C/351C/351M/400)) |
||
| Line 171: | Line 171: | ||
'''Blocks:''' | '''Blocks:''' | ||
| − | At some point during Australian production the casting "CF" at the top of the rear of the block, next to the oil pressure sensor outlet was changed to "GF". Also at some point late during production in an attempt to reduce the clevelands tendency to overheat, a "pillow" block was produced to increase water capacity | + | At some point during Australian production the casting "CF" at the top of the rear of the block, next to the oil pressure sensor outlet was changed to "GF". Also at some point late during production in an attempt to reduce the clevelands tendency to overheat, a "pillow" block was produced to increase water capacity around the cylinders. |
A "Nascar" block was produced by Ford Australia (exact year unknown) for the US market. Exact number shipped to the USA is unknown. These "Nascar" blocks were to have thicker cylinder walls and "better grade" cast iron, but due to bad core shift were no better than standard blocks. It is known however that most of these blocks were returned to Australia. These blocks were then used in regular production back in Australia. | A "Nascar" block was produced by Ford Australia (exact year unknown) for the US market. Exact number shipped to the USA is unknown. These "Nascar" blocks were to have thicker cylinder walls and "better grade" cast iron, but due to bad core shift were no better than standard blocks. It is known however that most of these blocks were returned to Australia. These blocks were then used in regular production back in Australia. | ||
| Line 177: | Line 177: | ||
Australian blocks have a "cast in" thermostat bypass plate, not stamped steel type. | Australian blocks have a "cast in" thermostat bypass plate, not stamped steel type. | ||
| − | '''Intake manifolds and | + | '''Intake manifolds and Carburetors:''' |
Australian built clevelands used either a Cast Iron 2bbl or 4bbl manifold in 2v size ports. Initially 302C's were only available with the 2bbl (1974-1976) and 351C's had either a 2bbl or 4bbl option. | Australian built clevelands used either a Cast Iron 2bbl or 4bbl manifold in 2v size ports. Initially 302C's were only available with the 2bbl (1974-1976) and 351C's had either a 2bbl or 4bbl option. | ||
| − | Rochester | + | Rochester carburetors were used on the 2bbls with an aluminum adapter plates. Carter Thermoquads were used on 4bbl spread bore type manifolds with an aluminum EGR plate. Early production 4bbl manifolds had large secondary inlet ports. Later production 4bbl manifolds had the secondary ports reduced in size in an effort to increase mileage and throttle response particularly on 302's with the 4bbl option. |
To confuse matters Australian production 351C motors were mixed with US built clevelands (mostly 4bbl Autolite motors) through to about 1976-77. Early Australian production 302C's 1973-1975 (XA-XB Falcon)used US blocks with Aussie heads and crankshaft/conrods. Then it appears that US built "C" blocks bought by Ford Australia were used up to the late 70's in regular production. | To confuse matters Australian production 351C motors were mixed with US built clevelands (mostly 4bbl Autolite motors) through to about 1976-77. Early Australian production 302C's 1973-1975 (XA-XB Falcon)used US blocks with Aussie heads and crankshaft/conrods. Then it appears that US built "C" blocks bought by Ford Australia were used up to the late 70's in regular production. | ||
Your Privacy Choices