John Deere Blitz Black paint

Jump to: navigation, search
(Part numbers)
Line 17: Line 17:
 
#Wait no longer than 3 hours to apply a second coat. However, one coat with the 8:1:1 paint-thinner-hardener ratio should be adequate.
 
#Wait no longer than 3 hours to apply a second coat. However, one coat with the 8:1:1 paint-thinner-hardener ratio should be adequate.
 
#A gallon will easily cover a small car.
 
#A gallon will easily cover a small car.
 +
 +
==Notes==
 +
*Be wary of striping, caused by the reducer drying too fast. To eliminate striping, some people recommend using regular enamel reducer instead of the John Deere reducer, for a slower evaporation rate.
 +
*Hold the gun at a 90 degree angle to the surface, and keep a 50% overlap.
 +
*John Deere Blitz Black paint can't be applied to high heat areas such as engine blocks, headers, or pipes. And, it will not retard rust.
 +
*It's reported to work well on fiberglass.
 +
*Urethane primer or epoxy primer may also be viable as undercoats for the JDBB paint.
 +
*Some say that JDBB paint is subject to fading and chalking over the years.
 +
*According to John Deere, yes, you can paint over JDBB paint with another coat of primer and/or enamel paint.
 +
*Opinions are mixed on using a clearcoat over JDBB. Some say that it can be applied if a flattening agent is used. Wet sanding and buffing for a glossy look is also recommended.
  
 
==Part numbers==
 
==Part numbers==
Line 25: Line 35:
 
*John Deere Reducer: PT158
 
*John Deere Reducer: PT158
 
*John Deere Hardener: REN3001
 
*John Deere Hardener: REN3001
 
==Cautions==
 
John Deere Blitz Black paint will not work on engine blocks, headers, pipes, or any other high-heat areas. And, it will not retard rust growth.
 
 
==Notes==
 
*Be wary of striping, caused by the reducer drying too fast. To eliminate striping, some people recommend using regular enamel reducer instead of the John Deere reducer, for a slower evaporation rate.
 
*Hold the gun at a 90 degree angle to the surface, and keep a 50% overlap.
 
*It's reported to work well on fiberglass.
 
*Urethane primer or epoxy primer may also be viable as undercoats for the JDBB paint.
 
*Some say that JDBB paint is subject to fading and chalking over the years.
 
*According to John Deere, yes, you can paint over JDBB paint with another coat of primer and/or enamel paint.
 
  
 
==Where to get it==
 
==Where to get it==
 
*[http://dealerlocator.deere.com/servlet/DealerLocator?command=home&locator=3&selectLocale=en_US&sessionId=Rgf865DJYGDkmUUhinR1QMN John Deere dealer locator]
 
*[http://dealerlocator.deere.com/servlet/DealerLocator?command=home&locator=3&selectLocale=en_US&sessionId=Rgf865DJYGDkmUUhinR1QMN John Deere dealer locator]
 
*[http://www.eberhardequipment.com/ Eberhard Equipment]
 
*[http://www.eberhardequipment.com/ Eberhard Equipment]
 
==Can I use a clearcoat with John Deere Blitz Black paint? How can I get a glossy look?==
 
Opinions are mixed on this. Although not intended for glossy black finishes, some say that a clearcoat can be applied over JDBB paint if a flattening agent is used. Or, try wet sanding or buffing.
 
  
 
==Photographs of JDBB paint jobs==
 
==Photographs of JDBB paint jobs==

Revision as of 20:39, 12 July 2006

Personal tools
Namespaces
Variants
Actions
Navigation
Categories
Toolbox