Bondo
(Blanked the page) |
m (Reverted edits by 72.10.121.33 (Talk) to last revision by 97.124.194.252) |
||
| Line 1: | Line 1: | ||
| + | {{newarticle}} | ||
| + | "Bondo" is a [http://en.wikipedia.org/wiki/Genericized_trademark genericized trademark] used to refer to plastic body fillers. Plastic body fillers are polyester resins that are mixed with hardeners into a putty. When they set, they become hard, and can be sanded, primed, and painted. | ||
| + | ==Bondo and health== | ||
| + | Bondo was developed as a replacement for lead used as body filler. It's less toxic, although it still poses health risks. Gloves, mask, and adequate ventilation are recommended. For MSDS details on specific Bondo products, [http://solutions.3m.com/wps/portal/3M/en_US/MSDS/Search/?gsaAction=msdsSRA&msdsLocale=en_US search the MSDS database at 3M.com]. | ||
| + | |||
| + | ==Types of plastic body filler== | ||
| + | *[http://solutions.3m.com/wps/portal/3M/en_US/3MAutomotive/Aftermarket/Products/Product-Catalog/?PC_7_RJH9U5230GE3E02LECFTDQCEK3_nid=02PKX0XCK6beFDKXQL309Jgl 3M body fillers and auto body repair products] | ||
| + | *[http://www.evercoat.com/products.aspx Evercoat] | ||
| + | *[http://solutions.3m.com/wps/portal/3M/en_US/3MAutomotive/Aftermarket/Products/Product-Catalog/?PC_7_RJH9U5230GE3E02LECFTDQCEK3_nid=MD5SPM1WHRgsFDKXQL309JglF3N1FCNSSKbl Marson Platinum Plus] | ||
| + | |||
| + | =="Waterproof" body fillers== | ||
| + | Be aware of "generous" marketing claims regarding waterproof body fillers. They are most likely "water-resistant", rather than actually "water-proof". Some people may choose to apply epoxy primer, then body filler, then epoxy primer over the filler. | ||
| + | |||
| + | If using a waterproof paint, a waterproof body filler may be unnecessary anyway. | ||
| + | |||
| + | ==Body filler tips== | ||
| + | *For body lines and peaks on hoods or doors, use a contour gauge to make a custom plastic filler spreader: | ||
| + | #Place the contour gauge on an undamaged area to get the contour. | ||
| + | #Trace the contour onto a plastic body filler spreader. | ||
| + | #Trim out the shape on the spreader. | ||
| + | *Cut filler spreaders to the desired size. | ||
| + | *To clean body filler spreaders, use 1/4 of a 3M scuff pad with lacquer thinner on it. A metal quart can with a lid makes a safe way to store the scuff pad along with some lacquer thinner. | ||
| + | *For reproducing small parts such as gaskets, use plastic body filler to make a mold: | ||
| + | #If the part doesn't already exist, a replica has to be made in its shape (for example, carve it out of soft plastic). | ||
| + | #Apply some wax to the part (this will act as a mold release), and lay it down on a piece of wax paper. | ||
| + | #Mix up some body filler, and place it in a small cup or bowl (the cap on a plastic jug may work). | ||
| + | #While the filler is still wet, place it over the part. | ||
| + | #When the filler hardens, it can be removed and used as a mold. | ||
| + | *When applying body filler upside down, apply the filler to a sheet of thin plastic (such as the side of a milk jug) and press it into place. When the filler hardens, peel the plastic away. | ||
| + | *Use an aluminum ruler to find high and low spots such as doors, hood to fender, trunk lid to fender, etc. | ||
| + | *If using filler with hatonite you can sand filler while still tacky. This will shred the filler smooth easily with hardly any pressure. When finished, follow up with a polyester glaze or add filler thinner to your final coat of filler. | ||
| + | |||
| + | |||
| + | ==DIY body filler recipes== | ||
| + | ''needs confirmation'' | ||
| + | *Epoxy resin and glass bubbles. | ||
| + | |||
| + | ==References== | ||
| + | *http://en.wikipedia.org/wiki/Bondo_(putty) | ||
| + | *http://www.hotrodders.com/forum/bondo-163104.html | ||
| + | |||
| + | [[Category:Body and exterior]] | ||
Your Privacy Choices