Body and exterior tips
(→Stripping paint) |
(→Stripping paint) |
||
| Line 43: | Line 43: | ||
If the paint is still shiny, before getting rid of it, use it to your advantage to find waves and dents in the body. | If the paint is still shiny, before getting rid of it, use it to your advantage to find waves and dents in the body. | ||
| − | === | + | ===Inspecting the panel before stripping=== |
| − | Here is an effective way to | + | Here is an effective way to inspect a quarter panel for imperfections. Move the vehicle outside or to a bright area. Place yourself near the back door and look toward the rear of the car. Focus on the panel's reflection of the objects in the vicinity. Move your head up and down, left and right, scanning the panel's entire area. Mark areas that reveal an imperfection with a pen and take pictures so you can remember to pay closer attention to them when doing body work. Repeat for every panel, door, hood, etc. |
===Methods of stripping paint=== | ===Methods of stripping paint=== | ||
| Line 56: | Line 56: | ||
====Chemical==== | ====Chemical==== | ||
| − | There | + | There exist a few brands of chemicals for stripping paint from vehicles. Although these strippers are effective, they are messy, and more importantly, they contain acid and emit toxic fumes and could be deadly if not used in properly ventilated areas. It is not recommended that they be used by novices. |
If you are a novice and still want to go through with this, this is how you do it. But I don't think you should. | If you are a novice and still want to go through with this, this is how you do it. But I don't think you should. | ||
| Line 63: | Line 63: | ||
These chemical strippers are more commonly used on hoods, roofs, and trunk lids as they need to be left alone after applying. The stripper would just run if put on a vertical panel and be somewhat ineffective. | These chemical strippers are more commonly used on hoods, roofs, and trunk lids as they need to be left alone after applying. The stripper would just run if put on a vertical panel and be somewhat ineffective. | ||
| + | |||
| + | |||
*Stripping a roof: Surrounding areas should be properly masked with several layers of tape and masking paper as stripper will work its way through tape glue. | *Stripping a roof: Surrounding areas should be properly masked with several layers of tape and masking paper as stripper will work its way through tape glue. | ||
| Line 68: | Line 70: | ||
*Stripping the trunk: Same as hood. Tie weight to the latch to keep the trunk from rising. | *Stripping the trunk: Same as hood. Tie weight to the latch to keep the trunk from rising. | ||
| + | All areas besides the areas you want to strip should be properly masked or removed. Stripper could seep behind a moulding and be problematic later. Stripper will damage plastic lenses. | ||
| + | |||
| + | After paint has lifted, scoop it up with a putty knife and discard the paint/stripper mixture into a carboard box. Don't get any on your skin. It burns. If you do, wash it off IMMEDIATELY with water. | ||
| + | |||
| + | Once you've scooped up most of the mixure, wash off the rest with water. It will dilute the stripper and render it | ||
| + | |||
| + | Wipe underneath the hood or trunk before reaching under it. Stripper will surely have seeped there and leave you with a nasty surprise. | ||
| + | |||
| + | After the area has been washed off, wipe it dry with a clean cloth. Remove any remaining paint or primer with an orbital sander using 40 to 80 grit. See Orbital Sander below | ||
====Orbital Sander==== | ====Orbital Sander==== | ||
| + | Removing paint from a panel using an orbital sander is the safest idea. Use 40 grit sandpaper for the quickest job. As you would be using the orbital sander for a prolonged period, wearing anti-vibration gloves might be a good idea. (I've never used them so I don't know how effective they are.) Not wearing gloves is no big deal. Your hands will just feel funny for a bit afterwards because of the exposure to the vibration. | ||
| + | |||
| + | After sanding off all traces of paint and primer, immediately spray on etching primer to keep ambient moisture from contaminating the panel. It is ESSENTIAL you heed to the following warning. It is a bit vulgar I must tell you, but for that reason it is an effective warning. It was given to me by a European painter I used to work with: "Always wear respirator when you spray etching primer. It kill your dick." | ||
===Methods of NOT stripping paint=== | ===Methods of NOT stripping paint=== | ||
Your Privacy Choices