How to find an electrical drain
(This was my first attempt at a wiki, it said to be bold, so I did it up right. A major Re-write) |
|||
| Line 1: | Line 1: | ||
{{youcanedit}} | {{youcanedit}} | ||
| − | + | # '''OVERVIEW''' | |
| + | If your vehicle engine fails to crank over and start after sitting overnight or longer but will start and run when "jumped" you may be experiencing an parasitic draw. (an excessive power drain when the vehicle is not in use.) | ||
| + | The test procedures below will help you to find the component(s) responsible if you are experiencing a parasitic draw. (electrical drain) | ||
| + | Parasitic draws occur when a component of your vehicle continues to use power from your battery when the vehicle is not in use. The most common causes are user controlled devices. Although anything that uses power can potentially go bad and cause a draw, some of the more common items are, phone chargers left plugged into a power point, lights (interior or exterior)left turned on, lighted vanity mirrors, cigarette lighters, glove compartment light, and aftermarket accessories (radio amps,CB's)left powered on. | ||
| + | # '''ACCEPTABLE AMPERAGE DRAW''' | ||
| + | ## Exact maximum allowable draw is determined by calculating several factors but as a general rule,the maximum should not excede 50mA or .050 Amps | ||
| + | # '''TOOLS AND EQUIPMENT''' | ||
| + | ## Battery Tester/Charger | ||
| + | ## Digital Volt Ohm Meter (DVOM) SET TO THE DC"AMP" SETTING | ||
| + | ## 12 volt test light | ||
| + | ## Proper hand tools to disconnect the negative battery cable | ||
| + | ## Suitable fuse puller (a small pair of needle nose pliers work well) | ||
| + | ## Wiring diagram of related circuits. (May need to obtain at a later time) | ||
| + | # '''PRELIMINARY INSPECTION''' | ||
| + | ## Test your battery and verify that it is capable of holding and has a full charge. | ||
| + | ## Using the test light, check all fuses and replace any that are blown. | ||
| + | ## Do a visual inspection of commmon problems. | ||
| + | ### On older vehicles you can get in the vehicle with all doors closed and perform visual. | ||
| + | ### On most late model vehicles equipped with a Vehicle Control Module (VCM)and/or Body Control Module (BCM) there may be a time out interval.(A certain amt of time has to pass in order for the VCM and/or BCM to enter sleep mode where the computers will use less power) These are vehicle specific and you will need to consult a proper service manual. | ||
| + | ## It is suggested that you consult the owners manual (if possible) in order to familiarize yourself with the location of all fuse boxes. You will also need to verify that you have a legend for the fuses telling you what amp fuse to use in each circuit and what components the fuses feed power to. At this time you will also need to determine which fuse feeds power to the interior lights. (often it is labeled "courtesy") | ||
| + | # '''TESTING''' | ||
| + | ## Ignition key off and all doors closed, and all aftermarket accessories turned off. If the vehicle is equipped with an underhood light you will need to disconnect the wires going to it, or remove the bulb. | ||
| + | ## Disconnect the negative battery cable. | ||
| + | ## '''Connecting DVOM''' | ||
| + | ### Make sure the DVOM cables stay connected to their correct locations (and not touching any other part of the vehicle) throughout the entire testing procedure(except when instructed otherwise). If they become disconnected you will need to perform step 3.3 again. | ||
| + | ### Connect the DVOM black cable(connected to the com port of the DVOM)to battery negative post | ||
| + | ### Connect the DVOM red cable (connected to the port labeled A) to the negative cable | ||
| + | ### Touch the negative cable end to the negative post of the battery for at least 15 seconds, then break the connection and let the meter reading become stable, record the reading. | ||
| + | #### Was the reading .050 A or less? | ||
| + | ##### Yes - You are not experiencing an excessive power draw at this time. | ||
| + | ##### No - You have a confirmed power draw continue with the next step. | ||
| + | ## Disconnect either one of the DVOM cables.(it is now safe for you to open the doors in order to gain access to the fuses). You will now need to remove the "courtesy" fuse, and perform step 4.3 again. | ||
| + | ### Did the reading remain the same(or very close) or did the amperage decrease? | ||
| + | #### Yes, it remained the same. - There is not a problem in this circuit at this time.Continue testing at step 4.5 | ||
| + | #### No, the amperage reading is less than before.- There is an excessive power draw in this circuit. If readings are now in the acceptable range you will now begin the isolation portion of this procedure. | ||
| + | ## Begin pulling the remaining fuses 1 at a time while monitoring DVOM readings after each fuse is removed. When the amperage reading drops to an acceptable range, note the circuit it dropped on, and reinstall the fuses already removed.Once all other fuses are installed verify the amperage is still below specification. If so, install fuse in suspect circuit and continue to the isolation portion of this test. | ||
| + | # '''ISOLATING THE DEVICE''' | ||
| + | ## Now that you know which circuit the draw is on, obtain a wiring diagram to determine what devices are powered by that circuit. | ||
| + | ## Now you will begin the process of unplugging devices (just like with the fuses, 1 at a time) until your meter drops within the acceptable range, when it does, you have found your culprit. | ||
| + | ## Replace That Part and perform step 4.3 again to verify repair. | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
[[Category:Electrical]] | [[Category:Electrical]] | ||
Your Privacy Choices