User contributions
(Latest | Earliest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)
- 20:14, 20 June 2011 (diff | hist) DynoSim combinations
- 17:45, 18 June 2011 (diff | hist) Camshaft/Compression Ratio relationships
- 17:39, 18 June 2011 (diff | hist) Camshaft/Compression Ratio relationships
- 17:36, 18 June 2011 (diff | hist) N Camshaft/Compression Ratio relationships (Created page with 'This article is taken from a thread where the Scandanavian OP was asking the following.... "How to Calculate wath Cinda Compression ratio a cam needs to work optimally and soo o…')
- 01:10, 15 June 2011 (diff | hist) DynoSim combinations
- 01:07, 15 June 2011 (diff | hist) DynoSim combinations
- 01:02, 15 June 2011 (diff | hist) DynoSim combinations
- 00:57, 15 June 2011 (diff | hist) DynoSim combinations
- 00:55, 15 June 2011 (diff | hist) DynoSim combinations
- 23:15, 14 June 2011 (diff | hist) Camshaft install tips and tricks (→Cleaning)
- 23:41, 6 June 2011 (diff | hist) Quadrajet
- 22:51, 6 June 2011 (diff | hist) Quadrajet
- 21:07, 28 May 2011 (diff | hist) Frame swaps
- 18:50, 27 April 2011 (diff | hist) DynoSim combinations
- 18:47, 27 April 2011 (diff | hist) DynoSim combinations
- 21:52, 8 April 2011 (diff | hist) N Decking a block (Created page with 'Setting the squish is a must-do if you expect optimum performance on pump gas. It is generally accepted that 0.035" to 0.045" is pretty much ideal. You can do it with a 0.025" pi…')
- 13:05, 25 October 2010 (diff | hist) Camshaft install tips and tricks (→Cleaning)
- 19:47, 17 October 2010 (diff | hist) Frame swaps
- 01:13, 15 October 2010 (diff | hist) N 383/388 Chevy stroker (Created page with 'All small block Chevy blocks are the same measurement from the centerline of the main bearing journals to the deck where the heads bolt on, ~9.025". When we mix and match compone…')
- 17:03, 4 October 2010 (diff | hist) How to find cam timing with motor assembled
- 17:01, 4 October 2010 (diff | hist) N How to find cam timing with motor assembled (Created page with 'Occasionally, we encounter a motor which we did not build, but want to know the cam timing without having to remove the cam to read the manufacturer's stamping on the rear face o…')
- 05:20, 30 September 2010 (diff | hist) Basic engine nomenclature
- 05:18, 30 September 2010 (diff | hist) Basic engine nomenclature
- 05:15, 30 September 2010 (diff | hist) N Basic engine nomenclature (Created page with '1. Piston deck height. This is the dimension from the crown of the piston to the flat deck of the block with the piston at top dead center. Nominally, with a premium 350 piston a…')
- 18:14, 3 September 2010 (diff | hist) N Cam and compression ratio compatibility (Created page with 'Sometimes it's difficult trying to explain to fellows who are new to hot rodding that you have to match the characteristics of the camshaft to the static compression ratio of the…')
- 14:59, 2 September 2010 (diff | hist) N Adjust valves SBC BBC (Created page with 'Remove spark plugs. Remove valve covers. Remove distributor. Standing at the front of the motor, at the water pump and looking toward the rear of the motor, #1 cylinder will be …')
- 01:48, 27 August 2010 (diff | hist) Camshaft install tips and tricks (→New flat tappet tools)
- 01:46, 27 August 2010 (diff | hist) Camshaft install tips and tricks (→Engine RPM for break in)
- 03:35, 7 August 2010 (diff | hist) Basic modifications for newbies
- 03:30, 7 August 2010 (diff | hist) Gasser
- 03:07, 7 August 2010 (diff | hist) Frame swaps (Replaced content with 'Category:Frame')
- 03:04, 7 August 2010 (diff | hist) Wheelbase, track width, and differential measurements
- 02:59, 7 August 2010 (diff | hist) NHRA-legal roll bar
- 02:43, 7 August 2010 (diff | hist) Camshaft install tips and tricks
- 02:42, 7 August 2010 (diff | hist) Camshaft install tips and tricks
- 02:37, 7 August 2010 (diff | hist) Dynamic compression ratio
- 02:36, 7 August 2010 (diff | hist) Determining top dead center
- 02:28, 7 August 2010 (diff | hist) Determining top dead center
- 02:27, 7 August 2010 (diff | hist) Determining top dead center
- 02:14, 7 August 2010 (diff | hist) Dynamic compression ratio (Replaced content with 'Have a nice day Crosley.')
- 02:13, 7 August 2010 (diff | hist) Bulletproof cooling system
- 02:01, 7 August 2010 (diff | hist) Basic modifications for newbies (Replaced content with ' Have a nice day Crosley.')
- 16:56, 6 August 2010 (diff | hist) Intake manifold/cylinder head internal vacuum leak
- 16:04, 6 August 2010 (diff | hist) Camshaft install tips and tricks
- 16:01, 6 August 2010 (diff | hist) Camshaft install tips and tricks
- 20:41, 5 August 2010 (diff | hist) Camshaft install tips and tricks (→Cleaning)
- 20:40, 5 August 2010 (diff | hist) Camshaft install tips and tricks
- 01:56, 1 August 2010 (diff | hist) NHRA-legal roll bar
- 18:57, 24 July 2010 (diff | hist) Camshaft install tips and tricks
- 01:15, 20 June 2010 (diff | hist) DynoSim combinations
(Latest | Earliest) View (newer 50 | older 50) (20 | 50 | 100 | 250 | 500)
Your Privacy Choices